ADE7752B

Rev. 0 | Page 6 of 24

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

F1

24

F2

23

S1

22

S0

21

CLKOUT

20

CLKIN

19

SCF

18

ABS

17

VCP

14

VAP

16

VN

13

VBP

15

ADE7752B

TOP VIEW

(Not to Scale)

Figure 3. Pin Configuration

Table 4. Pin Function Descriptions

Pin No.

Mnemonic

Description

1

CF

Calibration Frequency Logic Output. The CF logic output gives instantaneous active power information.

This output is intended to be used for calibration purposes.

2

DGND

This provides the ground reference for the digital circuitry in the ADE7752B, that is, multipliers, filters,

and digital-to-frequency converters. Because the digital return currents in the ADE7752B are small, it is

acceptable to connect this pin to the analog ground plane of the whole system.

3

Power Supply. This pin provides the supply voltage for the digital circuitry in the ADE7752B. The supply

voltage should be maintained at 5 V ± 5% for specified operation. This pin should be decoupled to

DGND with a 10 μF capacitor in parallel with a 100 nF ceramic capacitor.

4

REVP

This logic output goes logic high when negative power is detected on the sum of the three phase

powers. This output is not latched and resets when positive power is once again detected (see the

Negative Total Power Detection section).

5, 6;

7, 8;

9, 10

IAP, IAN;

IBP, IBN;

ICP, ICN

Analog Inputs for Current Channels. These channels are intended for use with current transducers and

are referenced in this document as current channels. These inputs are fully differential voltage inputs

with maximum differential input signal levels of ±0.5 V (see the Analog Inputs section). Both inputs

have internal ESD protection circuitry; in addition, an overvoltage of ±6 V can be sustained on these

inputs without risk of permanent damage.

11

AGND

This pin provides the ground reference for the analog circuitry in the ADE7752B (ADCs and reference).

This pin should be tied to the analog ground plane or the quietest ground reference in the system. This

quiet ground reference should be used for all analog circuitry, such as antialiasing filters and current

and voltage transducers. To keep ground noise around the ADE7752B to a minimum, the quiet ground

plane should connect to the digital ground plane at only one point. It is acceptable to place the entire

device on the analog ground plane.

12

This pin provides access to the on-chip voltage reference. The on-chip reference has a nominal value of

2.4 V ± 8% and a typical temperature coefficient of 25 ppm/°C. An external reference source can also be

connected at this pin. In either case, this pin should be decoupled to AGND with a 1 μF ceramic

capacitor.

13, 14, 15,

16

VN, VCP, VBP, VAP

Analog Inputs for the Voltage Channels. These channels are intended for use with voltage transducers

and are referenced in this document as voltage channels. These inputs are single-ended voltage inputs

with a maximum signal level of ±0.5 V with respect to VN for specified operation. All inputs have

internal ESD protection circuitry; in addition, an overvoltage of ±6 V can be sustained on these inputs

without risk of permanent damage.

17

ABS

This logic input is used to select the method by which the three active energies from each phase are

summed. It selects between the arithmetical sum of the three energies (ABS logic high) or the sum of

the absolute values (ABS logic low). See the Mode Selection of the Sum of the Three Active Energies section.

18

SCF

Select Calibration Frequency. This logic input is used to select the frequency on the calibration output

CF. Table 7 shows how the calibration frequencies are selected.

19

CLKIN

Master Clock for the ADCs and Digital Signal Processing. An external clock can be provided at this logic

input. Alternatively, a parallel resonant AT crystal can be connected across CLKIN and CLKOUT to

provide a clock source for the ADE7752B. The clock frequency for the specified operation is 10 MHz.

Ceramic load capacitors between 22 pF and 33 pF should be used with the gate oscillator circuit. Refer

to the crystal manufacturer’s data sheet for the load capacitance requirements.