ICS1893 datasheet(98/152 Pages) ICST

98 / 152 page

ICS1893 Rev C 6/6/00

June, 2000

Chapter 8

Management Register Set

ICS1893 Data Sheet - Release

8.13.2

Polarity Reversed (bit 18.14)

The Polarity Reversed bit is used to inform an STA whether the ICS1893 has detected that the signals on

the Twisted-Pair Receive Pins (TP_RXP and TP_RXN) are reversed. When the signal polarity is:

• Correct, the ICS1893 sets bit 18.14 to a logic zero.

• Reversed, the ICS1893 sets bit 18.14 to logic one.

Note:

The ICS1893 can detect this situation and perform all its operations normally, independent of the

reversal.

8.13.3

ICS Reserved (bits 18.13:6)

See Section 8.11.2, “ICS Reserved (bits 16.14:11)”, the text for which also applies here.

8.13.4

Jabber Inhibit (bit 18.5)

The Jabber Inhibit bit allows an STA to disable Jabber Detection. When an STA sets this bit to:

• Zero, the ICS1893 enables 10Base-T Jabber checking.

• One, the ICS1893 disables its check for a Jabber condition during data transmission.

8.13.5

ICS Reserved (bit 18.4)

See Section 8.11.2, “ICS Reserved (bits 16.14:11)”, the text for which also applies here.

8.13.6

Auto Polarity Inhibit (bit 18.3)

The Auto Polarity Inhibit bit allows an STA to prevent the automatic correction of a polarity reversal on the

Twisted-Pair Receive pins (TP_RXP and TP_RXN). If an STA sets this bit to logic:

• Zero (the default), the ICS1893 automatically corrects a polarity reversal on the Twisted-Pair Receive

pins.

• One, the ICS1893 either disables or inhibits the automatic correction of reversed Twisted-Pair Receive

pins.

Note:

This bit is also used to correct a reversed signal polarity for 100Base-TX operations.

8.13.7

SQE Test Inhibit (bit 18.2)

The SQE Test Inhibit bit allows an STA to prevent the generation of the Signal Quality Error pulse. When

an STA sets this bit to logic:

• Zero, the ICS1893 enables its SQE Test generation.

• One, the ICS1893 disables its SQE Test generation.

The SQE Test provides the ability to verify that the Collision Logic is active and functional. A 10Base-T

SQE test is performed by pulsing the Collision signal for a short time after each packet transmission

completes, that is, after TXEN goes inactive.

Note:

The SQE Test is automatically inhibited in full-duplex and repeater modes, thereby disabling the

functionality of this bit.

This bit is a control bit and not a status bit. Therefore, it is not updated to indicate this automatic

inhibiting of the SQE test in full-duplex mode or repeater mode.

ICS1893 датащи(PDF) 98 Page - Integrated Circuit Systems

ICS1893 датащи(HTML) 98 Page - Integrated Circuit Systems

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL