| поискавой системы для электроныых деталей |
|
ML22804 датащи(PDF) 33 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
ML22804 датащи(HTML) 33 Page - List of Unclassifed Manufacturers |
|
33 / 41 page ![]() FEDL2280XFULL-04 ML22808/ML22804/Ml22802-XXX 7. MUON command 0 1 1 1 ⎯ ⎯ ⎯ ⎯ • command M7 M6 M5 M4 M3 M2 M1 M0 1st byte 2nd byte The MUON command is a 2-byte command. This command is used to insert silence between the two playback phrases. The MUON command is enabled when the NCR signal is at a “H” level. Set the silence time length using the second byte of this command. As the silence length (M7 to M0), a value between 4 ms and 1024 ms can be set in 4 ms intervals (252 steps in total). The equation to set the silence time length is shown below. The silence length (M7-M0) must be set to 04h or higher. tmu = (2 7 ×(M7) + 26×(M6) + 25×(M5) + 24×(M4) + 23×(M3) + 22×(M2) + 21×(M1) + 20×(M0) + 1) × 4ms The timing diagram shown below is a case of inserting a silence of 20 ms between the repetitions of a phrase of (F7–F0) = 01h. CS Status Playing SCK DI NCR BUSY AOUT 1V Waiting for playback to be finished tcm tcm PLAY command 2 nd byte MUON command 1 st byte MUON command 2 nd byte PLAY command 1 st byte PLAY command 2 nd byte Awaiting command Address is being controlled Silence is being inserted Playing Waiting for silence insertion to be finished When the PLAY command is input, the address control of phrase 1 ends, the phrase playback starts, and the NCR signal goes “H” level. Input the MUON command after this NCR signal changes to the “H” level. After the MUON command input, the NCR signal remains “L” up to the end of phrase 1 playback, and the device enters a state waiting for the phrase 1 playback to end. When the phrase 1 playback finishes, the silence playback starts, and NCR1 signal goes “H” level. After this NCR signal has changed to the “H” level, re-input the PLAY command in order to play phrase 1. After the PLAY command input, the NCR signal once again returns to “L” level and the device enters the state waiting for the end of silence playback. When the silence playback finishes and then the phrase 1 playback starts, the NCR signal goes “H”, and the device enters a state in which it is possible to input the next PLAY or MUON command. The BUSY signal remains “L” until the end of a series of playback. 33/41 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |