MBRF2035CT THRU MBRF2060CT

SCHOTTKY ISOLATED PLASTIC RECTIFIER

Reverse Voltage - 35 to 60 Volts

Forward Current - 20.0 Amperes

FEATURES

¨ Isolated plastic package has Underwriters Laboratory

Flammability Classification 94V-0

¨ Dual rectifier construction, positive center tap

¨ Metal silicon junction,majority carrier conduction

¨ Low power loss, high efficiency

¨ High current capability, low forward voltage drop

¨ High surge capability

¨ Guardring for overvoltage protection

¨ For use in low voltage, high frequency inverters,

free wheeling, and polarity protection applications

¨ High temperature soldering guaranteed:

250

°C/10 seconds, 0.25" (6.35mm) from case

MECHANICAL DATA

Case: ITO-220AB fully overmolded plastic body

Terminals: Leads solderable per MIL-STD-750,Method 2026

Polarity: As marked

Mounting Position: Any

Weight: 0.08 ounce, 2.24 grams

Mounting Torque: 5 in. - lbs.max.

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25¡C ambient temperature unless otherwise specified.

SYMBOLS

MBRF2035CT

MBRF2045CT

MBRF2050CT

MBRF2060CT

UNITS

Maximum repetitive peak reverse voltage

35

45

50

60

Volts

Maximum working peak reverse voltage

35

45

50

60

Volts

Maximum DC blocking voltage

35

45

50

60

Volts

Maximum average forward rectified current

20.0

Amps

20.0

Amps

Peak forward surge current 8.3ms single half sine-

wave superimposed on rated load (JEDEC Method)

150.0

Amps

1.0

0.5

Amps

Maximum instantaneous

_

0.80

forward voltage per leg at

0.57

0.70

Volts

(NOTE 2)

0.84

0.95

0.72

0.85

Maximum instantaneous reverse current at

rated DC blocking voltage per leg

0.1

0.15

mA

15.0

150.0

dv/dt

10,000

V/

ms

5.0

¡C/W

Operating junction temperature range

-65 to +150

¡C

Storage temperature range

-65 to +175

¡C

RMS Isolation voltage from terminals to heatsink

with RH ² 30%

Volts

NOTES: (1) 2.0

(2) Pulse test: 300

ms pulse width, 1% duty cycle

(3) Thermal resistance from junction to case per leg

(4) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset.

(5) Clip mounting (on case, where leads do overlap heatsink.

(6) Screw mounting with 4-40 screw, where washer diameter is

£ 4.9 mm (0.19Ó).

Dimensions in inches and (millimeters)

NEW PRODUCT

NEW PRODUCT

NEW PRODUCT

2/18/99

0.060 (1.52)

0.405 (10.27)

0.383 (9.72)

0.676 (17.2)

0.646 (16.4)

0.191 (4.85)

0.171 (4.35)

0.600 (15.5)

0.580 (14.5)

0.560 (14.22)

0.530 (13.46)

0.037 (0.94)

0.027 (0.69)

0.140 (3.56)

0.130 (3.30)

0.350 (8.89)

0.330 (8.38)

0.188 (4.77)

0.172 (4.36)

0.110 (2.80)

0.100 (2.54)

0.131 (3.39)

0.122 (3.08)

0.110 (2.80)

0.100 (2.54)

0.022 (0.55)

0.014 (0.36)

0.105 (2.67)

0.095 (2.41)

0.205 (5.20)

0.195 (4.95)

PIN 1

PIN 3

PIN 2

1

3

PIN

2

DIA.

DIA.

ITO-220AB