AM1808 datasheet(51/265 Pages) TI1

51 / 265 page

AM1808

www.ti.com

SPRS653E – FEBRUARY 2010 – REVISED MARCH 2014

3.7.25 General Purpose Input Output

Table 3-27. General Purpose Input Output Terminal Functions

SIGNAL

POWER

TYPE(1)

PULL(2)

DESCRIPTION

GROUP(3)

NAME

NO.

GP0

ACLKR / PRU0_R30[20] / GP0[15] / PRU0_R31[22]

I/O

CP[0]

ACLKX / PRU0_R30[19] / GP0[14] / PRU0_R31[21]

I/O

CP[0]

AFSR / GP0[13] / PRU0_R31[20]

I/O

CP[0]

AFSX / GP0[12] /PRU0_R31[19]

I/O

CP[0]

AHCLKR / PRU0_R30[18] / UART1_RTS / GP0[11] /

I/O

CP[0]

PRU0_R31[18]

AHCLKX / USB_REFCLKIN / UART1_CTS / GP0[10] /

I/O

CP[0]

PRU0_R31[17]

AMUTE / PRU0_R30[16] / UART2_RTS / GP0[9] / PRU0_R31[16]

I/O

CP[0]

GPIO Bank 0

RTC_ALARM / UART2_CTS / GP0[8] / DEEPSLEEP

I/O

CP[0]

AXR15 / EPWM0TZ[0] / ECAP2_APWM2 / GP0[7]

I/O

CP[1]

AXR14 / CLKR1 / GP0[6]

I/O

CP[2]

AXR13 / CLKX1 / GP0[5]

I/O

CP[2]

AXR12 / FSR1 / GP0[4]

I/O

CP[2]

AXR11 / FSX1 / GP0[3]

I/O

CP[2]

AXR10 / DR1 / GP0[2]

I/O

CP[2]

AXR9 / DX1 / GP0[1]

I/O

CP[2]

AXR8 / CLKS1 / ECAP1_APWM1 / GP0[0] / PRU0_R31[8]

I/O

CP[3]

(1)

I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.

Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name

highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured

function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different

types (ie., input versus output), the table reflects the pin function direction for that particular peripheral.

(2)

IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using

the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the

device is out of reset. During reset, all of the pins associated with these registers are pulled down. If the application requires a pull-up,

an external pull-up can be used. For more detailed information on pullup/pulldown resistors and situations where external

pullup/pulldown resistors are required, see the Device Configuration section. For electrical specifications on pullup and internal pulldown

circuits, see the Device Operating Conditions section.

(3)

This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can

be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of

power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power

supply DVDD3318_C.

Device Overview

Submit Documentation Feedback

Product Folder Links: AM1808

AM1808 датащи(PDF) 51 Page - Texas Instruments

AM1808 датащи(HTML) 51 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL