DP2-21 datasheet(10/15 Pages) ETC2

10 / 15 page

kPa

MPa

kgf/cm2

bar

psi

mmHg

inHg

atm

(Torr)

1 kPa

10 3

1.01972

10 2

1.45038

10 1

7.50062

0.2953

9.86923

10 3

1 MPa

103

1.01972

1.45038

102 7.50062

103 0.2953

103

9.86923

1 kgf/cm2 9.80665

10 9.80665

10 2

9.80665

10 1 1.42234

7.35559

102

2.8959

10 9.67841

10 1

1 bar

102

10 1

1.01972

1.45038

7.50062

102

2.953

9.86923

10 1

1 psi

6.89473

10 3 7.03065

10 2 6.89473

10 2

5.17147

2.036

6.80457

10 2

1 mmHg

1.33322

10 1 1.33322

10 4 1.35951

10 3 1.33322

10 3 1.93368

10 2

3.9370

10 2 1.31579

10 3

(1 Torr)

1 inHg

3.3864

10 3 3.4531

10 2 3.3864

10 2

0.4912

2.5400

3.342

10 2

1 atm

1.01325

102 1.01325

10 1

1.03323

1.01325

1.46960

7.60000

102

2.9921

PRECAUTIONS FOR PROPER USE

DP2

801

Conversion procedure

Conversion table for pressure units

Conversion of pressure units

• In the DP2 series, the conversion

to different units is automatically

done on changing the setting of

the pressure unit. However, this

conversion can also be obtained

by multiplying the values by the

coefficients given in the table on

the right.

• For example, if 2 kPa is to be expressed

in kgf/cm2,

since 1 kPa

1.01972

10 2 kgf/cm2,

2 kPa becomes

1.01972

10 2 c 0.020 kgf/cm2.

Setting of key-protect

Key-protect function

• Key-protect is a function which prevents any unintentional

change in the conditions which have been entered in each

setting mode by making the sensor not to respond to the

key operations.

• In the sensing mode, press

key continuously

for about 3 sec. and release it immediately when

is displayed.

• Key-protect is set and the sensor returns to the

sensing mode.

MODE

Others

• Use within the rated pressure range.

• Do not apply pressure exceeding the pressure with-

standability value. The diaphragm will get damaged and

correct operation shall not be maintained.

• Do not use during the initial transient time (0.5 sec.) after

the power supply is switched on.

• Avoid use of standard type, flat type and light weight type

of sensors in places where steam and dust is excessive.

• Take care that the sensor does not come in direct contact

with water, oil, grease, or organic solvents, such as,

thinner, etc.

• Do not insert wires, etc., into the pressure port. The

diaphragm will get damaged and correct operation shall

not be maintained.

• Do not operate the keys with pointed or sharp objects.

DP2-20

–101.3kPa

OUT2

OUT1

MODE

0-ADJ

All models

Release of key-protect

• In the sensing mode, press

key continuously

for about 3 sec. and release it immediately when

is displayed.

• Key-protect is released and the sensor returns to the

sensing mode.

MODE

DP2-20

–101.3kPa

OUT2

OUT1

MODE

0-ADJ

DP2-21 датащи(PDF) 10 Page - List of Unclassifed Manufacturers

DP2-21 датащи(HTML) 10 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

датащи скачать

ссылки URL