MPP10(W)

Page

of 4

www.pduke.com

2013/7/9

3

OUTPUT SPECIFICATIONS

Parameter

Conditions

Min.

Typ.

Max.

Unit

Voltage accuracy

-1.0

+1.0

%

Line regulation

Low Line to High Line at Full Load

Single

Dual

-0.2

-0.5

+0.2

+0.5

%

Load regulation

No Load to Full Load

Single

Dual

-0.2

-1.0

+0.2

+1.0

%

Cross regulation

Asymmetrical load 25%/100% FL

Dual

-5.0

+5.0

%

Single output

3.3Vout, 5Vout, 12Vout

15Vout, 24Vout

-10

-10

+10

+20

%

Voltage adjustability

(Only for B-type Pin connection option)

Dual output

±5Vout, ±12Vout, ±15Vout

-10

+10

%

Ripple and noise

Measured by 20MHz bandwidth

With a 10µF/25V X7R MLCC

With a 4.7µF/50V X7R MLCC

3.3Vout, 5Vout

12Vout, 15Vout

24Vout

30

40

50

mVp-p

Temperature coefficient

-0.02

+0.02

%/ºC

Transient response recovery time

25% load step change

250

µ

s

Over voltage protection

Continuous clamp

3.3Vout

5Vout

12Vout

15Vout

24Vout

3.7

5.6

13.5

18.3

29.1

5.4

7.0

19.6

22.0

32.5

VDC

Over load protection

% of Iout rated; Hiccup mode

150

%

Short circuit protection

Continuous, automatics recovery

GENERAL SPECIFICATIONS

Parameter

Conditions

Min.

Typ.

Max.

Unit

Isolation voltage

1 minute

Input to Output

5000

VAC

Isolation capacitance

12

17

pF

Leakage current

240VAC,60Hz

2

µ

A

Switching frequency

270

300

330

kHz

Clearance/Creepage

8

mm

Design meet safety standard

ANSI/AAMI ES60601-1

IEC60601-1, EN60601-1

Case material

Non-conductive black plastic

Base material

Non-conductive black plastic

Potting material

Silicon (UL94-V0)

Dimensions

1.25 X 0.80 X 0.40 Inch

(31.8×20.3×10.2 mm)

Weight

14g (0.48oz)

MTBF

MIL-HDBK-217F Ta=25ºC, Full load (G/B, controlled environment)

8.638 x 10

ENVIRONMENTAL SPECIFICATIONS

Parameter

Conditions

Min.

Typ.

Max.

Unit

Without derating

,

-40

+77

ºC

Operating ambient temperature

With derating

+77

+105

ºC

Storage temperature range

-55

+125

ºC

Thermal impedance

Natural convection (20LFM)

18

ºC/W

Thermal shock

MIL-STD-810F

Vibration

MIL-STD-810F

Relative humidity

5% to 95% RH

EMC SPECIFICATIONS

Parameter

Conditions

Level

EN55011,EN55022 and FCC Part 18

Class A, Class B

ESD

EN61000-4-2

Air ± 8kV

Contact ± 6kV

Perf. Criteria A

Radiated immunity

EN61000-4-3

10 V/m

Perf. Criteria A

EN61000-4-4

± 2kV

Perf. Criteria A

EN61000-4-5

± 2kV

Perf. Criteria A

Conducted immunity

EN61000-4-6

10 Vr.m.s

Perf. Criteria A

Note:

1.

The MPP10(W) series can meet EMI Class A with no external filter. And Class B only with external components.

For more detail information, please contact with P-DUKE.

2.

An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5.

The MPP10-05S

recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 1000µF/25V).

And a reverse diode (Vishay V10P45) to connect in parallel.

The MPP10-12&24S

recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 470µF/50V).

The MPP10-48S

CAUTION: This power module is not internally fused. An input line fuse must always be used.