| поискавой системы для электроныых деталей |
|
EP5358LUI датащи(PDF) 12 Page - Altera Corporation |
|
|
|||||||||||||||||||||||||||||
EP5358LUI датащи(HTML) 12 Page - Altera Corporation |
|
12 / 16 page ![]() EP5358LUI/EP5358HUI VIN VSENSE VSO VS2 10 µF 4.7uF VOUT VOUT AGND ENABLE Ra Rb VFB VS1 PGND AVIN PVIN Figure 8: EP5358LUI using external divider The output voltage is selected by the following formula: ( ) Rb Ra OUT V V + = 1 6 . 0 Ra must be chosen as 237K Ω to maintain loop gain. Then Rb is given as: Ω − = 6 . 0 10 2 . 142 3 OUT b V x R VOUT can be programmed over the range of 0.6V to (VIN – 0.25V). NOTE: Dynamic Voltage Scaling is not allowed between internal preset voltages and external divider. EP5358HUI High VID Range Programming The EP5358HUI VOUT settings are optimized for higher nominal voltages such as those required to power IO, RF, or IC memory. The preset voltages range from 1.8V to 3.3V. There are eight (8) preset output voltage settings. The EP5358HUI does not have an external divider option. As with the EP5358LUI, the VID pin settings can be changed while the device is enabled. Table 2 shows the VS0-VS2 pin logic states for the EP5358HUI and the associated output voltage levels. A logic “1” indicates a connection to AVIN or to a “high” logic voltage level. A logic “0” indicates a connection to AGND or to a “low” logic voltage level. These pins can be either hardwired to AVIN or AGND or alternatively can be driven by standard logic levels. Logic levels are defined in the electrical characteristics table. Any level between the logic high and logic low is indeterminate. These pins must not be left floating. Table 2: EP5358HUI VID Voltage Select Settings Custom VID Setting Adjustment AVIN PVIN ENABLE VSENSE VOUT AGND PGND 5.0pF Rs 10uF 4.7uF EP5358xUI VS2 VS1 VSO Figure 9: EP5358xUI with RC inserted in VSENSE path to modify VID output voltages. It is possible to adjust VOUT for a given VID setting by inserting a parallel RC combination in the VSENSE path as shown in figure 9. The capacitor value is 5.0pF to ensure stability. Note that the value of VOUT can only be increased from its nominal setting (VOUTNEW>VOUTOLD): For EP5358LUI: kOhms VOUT VOUT Rs OLD NEW L − = 1 * 711 For EP5358HUI: kOhms VOUT VOUT Rs OLD NEW H − = 1 * 356 VOUTNEW is the desired “new” VOUT. VS2 VS1 VS0 VOUT 0 0 0 3.3 0 0 1 3.0 0 1 0 2.9 0 1 1 2.6 1 0 0 2.5 1 0 1 2.2 1 1 0 2.1 1 1 1 1.8 www.altera.com/enpirion Page 12 03541 October 11, 2013 Rev F |
|
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |