| поискавой системы для электроныых деталей |
|
EAEVALEDIP128B датащи(PDF) 4 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
EAEVALEDIP128B датащи(HTML) 4 Page - List of Unclassifed Manufacturers |
|
4 / 29 page ![]() EAeDIP160-7 Page 4 ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. RS-232 INTERFACE If the display is wired as shown below, the RS-232 interface is selected. The pin assignment is specified in the table on the right. The RxD and TxD lines lead CMOS level (VDD) to a microcontroller, for example, for direct connection. If “genuine” RS-232 levels are required (e.g. for connection to a PC), an external level converter (e.g. MAX232) is required. Baud rates Baud0 Baud1 Baud2 Data format 8,N,1 0 0 0 1200 1 0 0 2400 0 1 0 4800 1 1 0 9600 0 0 1 19200 1 0 1 38400 0 1 1 57600 1 1 1 115200 Note: The pins BAUD 0 to 2, ADR 0 to 2, DPOM, DPROT and TEST/SBUF have an internal pullup, which is why only the LO level (0=GND) is to be actively applied. These pins must be left open for a hi level. For RS232 operation (without addressing) the pins ADR 0 to ADR 2 must be left open. On pin 20 (SBUF) the display indicates with a low level that data is ready to be retrieved from the internal send buffer. The line can be connected to an interrupt input of the host system, for example. BAUD RATES The baud rate is set by means of pins 6, 7 and 8 (baud 0 to 2). The data format is set permanently to 8 data bits, 1 stop bit, no parity. RTS/CTS handshake lines are not required. The required control is taken over by the integrated software protocol (see pages 10 and 11). Pinout eDIP160-7: RS-232/RS-485 mode Pin Symbol In/Out Function Pin Symbol In/Out Function 1 GND Ground Potential for logic (0V) 21 GND Ground (0V) 2 VDD Power supply for logic (+3,3V..5V) 22 VDD Power supply (+3,3..5V) 3 NC do not connect 23 NC do not connect 4 NC do not connect 24 NC 5 RESET In L: Reset 25 IN8 / OUT1 8 digital inputs (internal 20k..50k pullup) alternativ up to 8 digital outputs maximum current: IOL = IOH = 10mA 6 BAUD0 In Baud Rate 0 26 IN7 / OUT2 7 BAUD1 In Baud Rate 1 27 IN6 / OUT3 8 BAUD2 In Baud Rate 2 28 IN5 / OUT4 9 ADR0 In Address 0 for RS-485 29 IN4 / OUT5 10 RxD In Receive Data 30 IN3 / OUT6 11 TxD Out Transmit Data 31 IN2 / OUT7 12 EN485 Out Transmit Enable for RS-485 driver 32 IN1 / OUT8 13 WUP In L: (Power-On) disable Power-On-Macro L: Wakeup from Powerdownmode 33 NC do not connect 14 ADR1 In Address 1 for RS-485 34 NC 15 ADR2 In Address 2 for RS-485 35 NC 16 BUZZ Out H: Buzzer output (L: Buzzer off) 36 NC 17 DPROT In L: Disable Smallprotokoll do not connect for normal operation 37 NC 18 PWR Out L: Normal Operation H: Powerdownmode 38 NC 19 NC do not connect 39 NC 20 TEST SBUF IN Out open-drain with internal pullup 20k..50k IN (Power-On) L: Testmode OUT L: data in sendbuffer 40 NC Application example |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |