MPL-05SE datasheet(2/2 Pages) MPD

2 / 2 page

Model Selection Guide

Notes:

• All dimensions are typical in inches (mm)

• Tolerance x.xx = ±0.02 (±0.50)

Function

AC-Neutral

-VCAP

AC-Line

-VOUT

5+VCAP

+VOUT

Pin Connections

Model

Number

Output

Voltage

Accuracy

(%)

Max

Capacitive

Load

(µF)

Efﬁciency

(%, Typ)

Voltage

(VDC)

Current

(mA Max.)

MPL-05S-03E

3.3

1,000

±2.0

1,000

MPL-05S-05E

5.0

1,000

±1.0

1,500

MPL-05S-09E

9.0

560

±1.0

630

MPL-05S-12E

12.0

420

±1.0

470

MPL-05S-15E

15.0

340

±1.0

330

MPL-05S-24E

24.0

210

±1.0

100

Derating Curve

Mechanical Dimensions

MicroPower Direct

We Power Your Success - For Less!

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

www.micropowerdirect.com

Typical Connection

1. It is recommended that an external fuse and NTC be used. The recommended

fuse is a 1.0A/250V slow blow and for the NTC, a 5D-9.

2. An external MOV is recommended on the input to protect the unit in the event of

a surge. A 561KD14 or equivalent is recommended.

3. The ﬁlter capacitor C1is required for speciﬁed operation.The recommended value

is 33 µF/400V.

4. The safety capacitors (Cx1 and CY0) provide EMI/RFI suppresion. Recommended

values are 0.22 µF/275 VAC (Cx1) and 1 nF/400 VAC (CY0).

5. Recommended values for other components are:

Output

TVS

3.3V

470 µF/16V

0.47 µH

150 µF/35V

100 nF/50V SMBJ7.0A

5.0V

470 µF/16V

0.47 µH

150 µF/35V

100 nF/50V SMBJ7.0A

9.0V

330 µF/35V

1.0 µH

150 µF/35V

100 nF/50V

SMBJ12A

12V

330 µF/35V

1.0 µH

150 µF/35V

100 nF/50V

SMBJ20A

15V

330 µF/35V

1.0 µH

150 µF/35V

100 nF/50V

SMBJ20A

24V

100 µF/35V

4.7 µH

47 µF/35V

100 nF/50V

SMBJ30A

The output ﬁltering capacitors (C2,C3) are high frequency, low resistance electro-

lytic capacitors. Capacitor (C4) is ceramic. Voltage derating of capacitors should

be 80% or above.

6. Input noise and surge suppression modules are available for a number of MPD

AC/DC power supplies.An MPL-05SE connection with theACFM-01 is illustrated

in the diagram at left. For pricing or full technical information on these modules

(ACFM-01 and ACFM-02) please contact the factory.

Notes:

1. Operation at no load will not damage the units, however, they may not meet all speciﬁcations.

2. All units are rated for EN 55022 (CE/RE) class A with the addition of external components such

as the typical circuit shown below. They will meet class B with the addition of the ACFM-01 (or a

similar discrete ﬁlter circuit). Contact the factory for more information.

3. To meet the requirements of EN 61000-4-4 (±4 kV), external components are needed. This

can be done discretely, or with the addition of the ACFM-01. Contact the factory for more

information.

4. To meet the requirements of EN 61000-4-5 (±4 kV/±4 kV), external components are needed.

This can be done discretely, or with the addition of the ACFM-01. Contact the factory for more

information.

5. It is recommended that a fuse be used on the input of a power supply for protection. For

the MPL-05SE series, a 1.0A/250 VAC slow blow should be used.

Input Voltage Vs Load

The diagram below illustrates a typical application connection of the MPL-05SE series. Notes on this circuit (starting with the input circuit) are:

Typical Board Layout: With ACFM-01 Input Module (See note 6)

MPL-05SE датащи(PDF) 2 Page - MicroPower Direct, LLC

MPL-05SE датащи(HTML) 2 Page - MicroPower Direct, LLC

Html Pages

1 2

датащи скачать

ссылки URL