MicroPower Direct

We Power Your Success - For Less!

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

www.micropowerdirect.com

Model Selection Guide

Model

Number

Input

Output

Efficiency

(%, Typ)

Reflected

Ripple

Current

(mA Typ)

Capacitive

Load

(µF, Max)

Fuse

Rating

Slow-Blow

(mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load No-Load

MA624S-05RUI

24

9.0 - 36.0

214

20

3.3

1,200.0

0.0

77

20.0

470

1,500

MA624S-05RUI

24

9.0 - 36.0

313

20

5.0

1,200.0

0.0

80

20.0

470

1,500

MA624S-12RUI

24

9.0 - 36.0

298

20

12.0

500.0

0.0

84

20.0

100

1,500

MA624S-15RUI

24

9.0 - 36.0

298

20

15.0

400.0

0.0

84

20.0

100

1,500

MA624S-24RUI

24

9.0 - 36.0

298

20

24.0

250.0

0.0

84

20.0

47

1,500

MA624D-05RUI

24

9.0 - 36.0

260

20

±5.0

±500.0

±0.0

80

20.0

±100

1,500

MA624D-12RUI

24

9.0 - 36.0

298

20

±12.0

±250.0

±0.0

84

20.0

±100

1,500

MA624D-15RUI

24

9.0 - 36.0

298

20

±15.0

±200.0

±0.0

84

20.0

±100

1,500

MA648S-03RUI

48

18.0 - 75.0

107

10

3.3

1,200.0

0.0

77

15.0

470

800

MA648S-05RUI

48

18.0 - 75.0

156

10

5.0

1,200.0

0.0

80

15.0

470

800

MA648S-12RUI

48

18.0 - 75.0

149

10

12.0

500.0

0.0

84

15.0

100

800

MA648S-15RUI

48

18.0 - 75.0

149

10

15.0

400.0

0.0

84

15.0

100

800

MA648S-24RUI

48

18.0 - 75.0

149

10

24.0

250.0

0.0

84

15.0

47

800

MA648D-05RUI

48

18.0 - 75.0

130

10

±5.0

±500.0

±0.0

80

15.0

±100

800

MA648D-12RUI

48

18.0 - 75.0

149

10

±12.0

±250.0

±0.0

84

15.0

±100

800

MA648D-15RUI

48

18.0 - 75.0

149

10

±15.0

±200.0

±0.0

84

15.0

±100

800

For 1.5 kV Isolation, See MA600x-xxRU Series Datasheet

For 2:1 Inputs, See MA600x-xxRW Series Datasheet

Mechanical Notes:

Notes:

1. When measuring output ripple, it is recommended that an external 3.3 µF ceramic capacitor be

for dual output units.

2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%.

3. Operation at no-load will not damage these units.

4. An external 220 µF/100V capacitor connected across the input pins is required to meet

EN61000-4-4 and EN61000-4-5.

5. Dual output units may be connected to provide a 10, 24 or 30 VDC output. To do this, connect the

6. The converter should be connected to a low ac-impedance source. An input source with a highly

inductive impedance may affect the stability of the converter. In applications where the converter

output loading is high and input power is supplied over long lines, it may be necessary to use

a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR

<1.0

at 100 kHz) capacitor be mounted close to the converter. For 24V input units a 4.7 µF is

recommended; and for 48V units a 2.2 µF.

7. It is recommended that a fuse be used on the input of a power supply for protection. See the table

above for the correct rating.

Pin

Single

Dual

2, 3

9

No Pin

Common

11

NC

14

16

Common

22, 23

NC: No Connection

Pin Connections

Mechanical Dimensions

Derating Curve