139RPFS datasheet(3/9 Pages) MAXWELL

3 / 9 page

All data sheets are subject to change without notice

Quad Comparators, Low Offset Voltage

139

04.08.08 Rev1

TABLE 5. 139 ELECTRICAL CHARACTERISTICS

(V+ = 5V, T

A = -55 TO 125° C, UNLESS OTHERWISE SPECIFIED)

PARAMETER

SYMBO

TEST CONDITIONS

SUB-

GROUPS

MIN

TYP

MAX

UNIT

Input Offset Voltage

1. At output switch point, V

O=1.4V, RS=0Ω with V+ from 5VDC to 30 VDC; and over the full input common-mode range (0VDC to V+-

1.5V

DC).

+25°C

-55 to 125°C

2,3

Input Bias Current

IN(+) or IIN(-) with Output in Linear

Range,2, V

CM = 0V

2. The direction of the input current is out of the IC due to the PNP input stage. This current essentially constant, independent of the

state of the output so no loading change exists on the reference or input lines.

+25°C

100

-55 to 125°C

2,3

300

Input Offset Current

IN(+) - IIN(-), VCM = 0V

+25°C

-55 to 125°C

2,3

100

Input Common Mode

Voltage Range

V+ = 30 V

3. The input common-mode voltage or either input voltage signal should not be allowed to go negative by more than 0.3V. The upper

end of the common-mode voltage range is V+-1.5V at 25°C, but either or both inputs can go to +30V without damage, independent of

the magnitude of V+.

+25°C

V+ -1.5

-55 to 125°C

2,3

V+ -2.0

Supply Current

L=∞on all comparators, V+ = 30V

+25°C

0.8

2.0

-55 to 125°C

2,3

3.0

Voltage Gain

L > 15kΩ, V+=15VDC;

O = 1VDC to 11 VDC

( To support large V

O swing)

+25°C

200

V/mV

Large Signal Response

Time

IN = TTL Logic Swing,

REF = 1.4V, VRL = 5V

DC,

I = 5.1kΩ

+25°C

300

Response Time

Rtil

RL = 5V

DC, RL = 5.1kΩ

4. The response time specified is for a 100mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained.

+25°C

1.3

µ s

Output Sink Current

SINK

IN(-) = 1VDC, VIN(+) = 0,

O < 1.5VDC

+25°C

6.0

Saturation Voltage

SAT

IN(-) > 1V, VIN(+) = 0,

SINK < 4 mA

+25°C

250

400

-55 to 125°C

2,3

700

Output Leakage Current

CEX

IN(+) = 1VDC, VIN(-) = 0,

O = 5VDC VIN(-) = 0

+25°C

0.1

-55 to 125°C

2,3

1.0

µ A

Differential Input Voltage

diff

Keep all V

IN’s > 0 VDC

(or V- if used)5

5. Positive excursions of input voltage may exceed the power level as long as the other voltage remains within the common mode range,

the comparator will provide a proper output state. The low input voltage state must not be less than -0.3 V

DC (or 0.3VDC below the

magnitude of the negative power supply, if used) (at 25°C).

-55 to 125°C

2,3

139RPFS датащи(PDF) 3 Page - Maxwell Technologies

139RPFS датащи(HTML) 3 Page - Maxwell Technologies

Html Pages

1 2 3 4 5 6 7 8 9

датащи скачать

ссылки URL