CXOL datasheet(2/2 Pages) STATEK

2 / 2 page

SPECIFICATIONS: CXOL

Specifications are typical at 25OC unless otherwise noted.

Specifications are subject to change without notice.

Supply Voltage

1.2 V - 5.0 V 10%

Current Consumption

32.768 kHz (2.8 µA)1

32.768 kHz (0.4 µA)2

100.0 kHz

(8.0 µA)1

Calibration Tolerance3

20 ppm,

50 ppm or

100 ppm

Voltage Coefficient

1 ppm/V

Output load (CMOS)4

10 pF

Aging, first year

2 ppm

Shock, survival

5000 g peak, 0.3 ms,1/2 sine

Vibration, survival

20 g, 10 -2000 Hz swept sine

Startup Time

200 ms

Operating Temperature

-10OC to +70OC (Commercial)

-40OC to +85OC (Industrial)

-55OC to +125OC (Military)

1. VDD = 3.3V and 10 pF load.

2. VDD = 3.3V, 10 pF load and OE is low.

3. Tighter calibration tolerances available. Please contact factory.

4. Other loads available. Please contact factory.

STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com

10205 Rev A

ELECTRICAL CHARACTERISTICS

CXOL 32.768 kHz

All parameters are measured at 25ºC with a 10MΩ and

10pF load with VDD 3.3 V.

SYMBOL PARAMETER

MIN.

TYP. MAX. UNIT

Output Voltage Hi VDD-0.4 VDD

VOutput Voltage Lo

0.4

SYM

Duty Cycle

Rise Time (10%-90%)

nsec.

Fall Time (10%-90%)

nsec.

HOW TO ORDER CXOL SURFACE MOUNT CRYSTAL OSCILLATORS

CXOL

SM3

32.768K

Frequency

K = kHz

1 = 1.8V

2 = 2.5V

3 = 3.0V

4 = 3.3V

5 = 5.0V

“S” if special or

custom design.

Blank if Std.

Blank = SM1

=Gold Plated

(Lead Free)

SM2 = Solder Plated

SM3 = Solder Dipped

SM4 = Solder Plated

(Lead Free)

SM5 = Solder Dipped

(Lead Free)

Calibration

Tolerance

@ 25OC

(in PPM)

Temp. Range:

C= -10°C to +70°C

I=-40°Cto+85°C

M = -55°C to +125°C

T = Tri-State

N = no

connection

PIN CONNECTIONS

Connection

1Output

2Ground

3Output Enable (T) or NC

4VDD

Tri-State (Pin 3 High*) Disable (Pin 3 Low)

Output

Frequency Output

High Z State

Internal Osc.

Oscillates

Current

Normal

Lower than Normal

TRISTATE/DISABLE OPTIONS (T/N)

Statek offers two enable/disable options: T and N. The T-

version has a Tri-State output and continues oscillating

internally when the output is put into the high Z state. The

N-version does not have PIN 3 connected internally and so

has no Tri-State/Disable capability. The following table

describes the Tri-State/Disable option T.

* When PIN 3 is allowed to float, it is held high by an internal pull-up resistor.

TRISTATE/DISABLE OPTION T

FUNCTION TABLE

ABSOLUTE MAXIMUM RATINGS

Supply Voltage VDD

-0.5V to 7V

Storage Temperature

-55OC to +125OC

Process Temperature

260OC, 2 min.

PACKAGING OPTIONS

CXOL -Tray Pack

-12 mm carrier tape, 7”or 13” reels

Per EIA 481 (see Tape and Reel data sheet 10109)

CXOL датащи(PDF) 2 Page - STATEK CORPORATION

CXOL датащи(HTML) 2 Page - STATEK CORPORATION

Html Pages

1 2

датащи скачать

ссылки URL