MP2007 – 3A, 1.3V-6.0V INPUT, DDR MEMORY TERMINATION REGUALTOR

MP2007 Rev. 0.2

www.MonolithicPower.com

9

7/23/2009

MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.

© 2009 MPS. All Rights Reserved.

APPLICATION INFORMATION

Input Capacitor

Depending on the trace impedance from the

power supply to the part, transient increase of

source current is supplied mostly by the charge

from the VDDQ input capacitor. Use a 10μF (or

more) ceramic capacitor to supply this transient

charge. Provide more input capacitance as more

output capacitance is used at VTT. In general,

use 1/2 COUT for input.

Output Capacitor

For stable operation, total capacitance of the VTT

output terminal can be equal or greater than

20μF. Attach two 10μF ceramic capacitors in

parallel to minimize the effect of ESR and ESL. If

the ESR is greater than 10m

Ω, insert an R-C

filter between the output and the VTTSEN input

to achieve loop stability. The R-C filter time

constant should be almost the same or slightly

lower than the time constant of the output

capacitor and its ESR.

VDRV Capacitor

Add a ceramic capacitor with a value between

1.0μF and 4.7μF placed close to the VDRV pin,

to stabilize 5V from any parasitic impedance from

the supply.

Thermal design

As the MP2007 is a linear regulator, the VTT

current flow in both source and sink directions

generate power dissipation from the device.

In the source phase, the potential difference

between VDDQ and VTT times VTT current

becomes

the

power

dissipation,

Psource=(VDDQ-VTT) x Isource

In this case, if VDDQ is connected to an

alternative power supply lower than VDDQ

voltage, power loss can be decreased.

For the sink phase, VTT voltage is applied across

the internal LDO regulator, and the power

dissipation Psink is:

Psink=VTT x Isink

The device does not sink and source the current

at the same time and source/sink current varies

rapidly with time. The actual power dissipation to

be considered for thermal design is an average

of the above values over time.

Another power consumption is the current used

for internal control circuitry from VDDQ supply.

This power needs to be effectively dissipated

from the package.

PCB Layout Guidelines

Good PCB layout design is critical to ensure high

performance and stable operation of the DDR

power controller. The following items must be

considered when preparing PCB layout:

1. All high−current traces must be kept as short

and wide as possible to reduce power loss.

High−current traces are the trace from the input

voltage terminal to VDDQ pin, the trace from the

VTT output terminal to the load, the trace from

the input ground terminal to the VTT output

ground terminal, and the trace from VTT output

ground terminal to the GND pin.

Power handling and heaksinking of high−current

traces can be improved by also routing the same

high−current traces in the other layers by the

same path and joining them together with

multiple vias.

2. To ensure the proper function of the device,

separated ground connections should be used

for different parts of the application circuit

according to their functions.

The VTT output capacitor ground should be

connected to the GND pin first with a short trace,

it is then connected to the ground plane of GND.

The input capacitor ground, the VTT output

capacitor

ground,

the

VDDQ

decoupling

capacitor ground should be connected to the

GND plane.

3. The thermal pad of the 8-pin MSOP package

should to be connected to GND for better thermal

performance. It is recommended to use a PCB

with 1 oz or 2oz copper foil.

4. A separate sense trace should be used to

connect the VTT point of regulation, which is

usually the local bypass capacitor for load, to the

VTTSEN pin.

5. Separate sense trace should be used to

connect the VREF point of regulation to the

VTTREF pin to ensure the accuracy of

the

reference voltage to VTT.