 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
PC06E8-2S. датащи(PDF) 29 Page - Amphenol Corporation |
|
|
|||||||||||||||||||||||||||||
PC06E8-2S. датащи(HTML) 29 Page - Amphenol Corporation |
|
|
29 / 80 page  27 PT, SP To more easily illustrate ordering procedure, part number PT00A-20-41PW(SR) is shown as follows: PT 00 A - 20 - 41 P W (SR) 1 2345678 See code below: 1. Connector Type “PT” designates standard olive drab, electrically conductive cadmium plate bayonet lock connector with solder contacts “SP” designates electrically non-conductive, hard anodic coated bayonet lock connector with solder contacts and larger flange and mounting holes for back panel mounting “PTG” designates plug with grounding fingers 2. Shell Style “00” designates wall mounting receptacle “01” designates cable connecting receptacle** “02” designates box mounting receptacle “06” designates straight plug “07” designates jam nut receptacle “08” designates 90 degree plug cable support “B” designates thru bulkhead receptacle (pressurized) “ I” designates solder mount receptacle (Hermetic only) 3. Service Classes “A” designates general duty back shell “C” designates pressurized receptacle “E” designates environmental resisting open wire seal with grommet and nut “J” designates clamp assembly for moisture proofing multi-jacketed cables, with strain relief “P” designates assembly with potting boot W” designates clamp assembly for moisture proofing multi-jacketed cables “H” designates hermetic* without interfacial seal “Y” designates hermetic* with interfacial seal 4. Shell Size “20” designates shell size. Shell sizes 6 through 24 available. 5. Insert Arrangement - Refer to pages 4-11 for insert availability. “20 - 41” designates insert arrangement. (The number following the hyphen is the number only that is used in the part number). 6. Contacts “P” designates pin contacts “S” designates socket contacts For ordering connectors with printed circuit board contacts, see pg. 20. 7. Insert Rotation - Refer to page 7. “W”, “X”, “Y”, “Z” designate that insert is rotated in its shell from “normal position. No letter required for normal (no rotation) position. 8. “SR” designates a strain relief clamp. Indicate optional finishes as follows: (003) olive drab cadmium plate (standard on “PT”) (005) anodic coating - Alumilite® (standard on “SP”) (014) olive drab cadmium plate over nickel (023) electroless nickel (024) olive drab zinc cobalt plating (424) electroless nickel finish with strain relief (466) olive drab zinc cobalt plating with strain relief (100) Suffix added for flat eyelet pin contacts in hermetic versions OR RoHS Compliant finish suffix as follow: (025) non-conductive black zinc cobalt plating (027) conductive black zinc cobalt plating (470) non-conductive black zinc cobalt plating with strain relief (476) conductive black zinc cobalt plating with strain relief MS/PT MIL-C-26482, Series 1 Part number MS3110E20-41PW is shown as follows: MS 311 0 E 20 - 41 P W 1 2345678 For Hermetic connectors part number MS3113H20Y41PW is shown as follows: MS 311 3 H 20 Y 41 P W 1 234 5, 6 7 8 See code below: 1. “MS” designates Military Standard 2. Specification Number “311” designates basic family number for MIL-C- 26482, Series 1 solder type 3. Shell Style “0” designates wall mounting receptacle “1” designates cable connecting receptacle** “2” designates box mounting receptacle “3” designates solder mount receptacle (hermetic only) “4” designates jam nut receptacle “6” designates straight plug 4. Service Class “E” designates environmental resisting connector “F” designates environmental resisting connectors with strain relief “J” designates clamp assembly for moisture proofing multi-jacketed cables, with strain relief “P” designates potted type with potting boot “H” designates hermetic 5. Shell Size “20” designates shell size. Shell sizes 8 through 24 available. 6. Insert Arrangement - Refer to pages 4-11 for insert availability. “20 - 41” designates arrangement. (The number fol- lowing the hyphen is the number only that is used in the part number). Hermetic version “20Y41” designates insert arrangement; specify “Y” for flat eyelet pin contacts, or “C” for solder cup pin contacts 7. Contact Configuration “P” designates pin contacts “S” designates socket contacts 8. Insert Rotation- Refer to page 7. “W”, “X”, “Y”, “Z” designate that insert is rotated in it shell from “normal” position. No letter require fo nor- mal (no rotation) position. * Hermetic connectors are supplied with tin plated shells. ** This connector style is sometimes referred to as a cable connect- ing “plug”. It does, however, mate with either a straight or 90 degree plug. For ordering Miniature Breakaway PT Solder connec- tors see pg. 26. PT, SP, MS/PT how to order Ro HS Am phenol U / 2002 / 95 / E |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
