TLK2501

1.5 TO 2.5 GBPS TRANSCEIVER

SLLS427D − AUGUST 2000 − REVISED JULY 2003

6

POST OFFICE BOX 655303

Terminal Functions (Continued)

TERMINAL

TYPE

DESCRIPTION

NAME

NO.

TYPE

DESCRIPTION

RX_CLK

41

O†

Recovered clock. Output clock that is synchronized to RXD, RX_ER, RX_DV/LOS. RX_CLK is

the recovered serial data rate clock divided by 20. RX_CLK is held low during power-on reset.

RX_ER/

PRBS_PASS

29

O‡

Receive error. When RX_ER and RX_DV/LOS are asserted, indicates that an error was

detected somewhere in the frame presently being output on the receive data bus. When RX_ER

is asserted and RX_DV/LOS is deasserted, indicates that carrier extension data is being

presented (see Table 2). The RX_ER is in high-impedance state during power-on reset.

When PRBSEN= low (deasserted), this terminal is used to indicate receive error (RX_ER).

When PRBSEN = high (asserted), this terminal indicates status of the PRBS test results

(High=pass).

RX_DV/

LOS

30

O‡

Receive data valid. RX_DV/LOS is output by the transceiver to indicate that valid recovered and

decoded data is being output on the receive data bus. RX_DV/LOS is asserted high continuously

from the first recovered word of the frame through the final recovered word and is negated prior

to the first rising edge of RX_CLK that follows the final word (see Table 2). The RX_DV/LOS is

in high-impedance state during power-on reset.

If, during normal operation, the differential signal amplitude on the serial receive terminals is

below 200 mV, RX_DV/LOS is asserted high along with RX_ER and the receive data bus to

indicate a loss of signal condition. If the device is in power-down mode, RX_DV/LOS is the output

of the signal detect circuit and is asserted low when a loss of signal condition is detected.

TESTEN

27

I

Test mode enable. This terminal should be left unconnected or tied low.

TXD0

TXD1

TXD2

TXD3

TXD4

TXD5

TXD6

TXD7

TXD8

TXD9

TXD10

TXD11

TXD12

TXD13

TXD14

TXD15

62

63

64

2

3

4

6

7

10

11

12

14

15

16

17

19

I§

Transmit data bus. These inputs carry the 16-bit parallel data output from a protocol device to

the transceiver for encoding, serialization, and transmission. This 16-bit parallel data is clocked

into the transceiver on the rising edge of GTX_CLK as shown in Figure 10.

TX_EN

20

I§

Transmit enable. TX_EN in combination with TX_ER indicates the protocol device is presenting

data on the transmit data bus for transmission. TX_EN must be high with the first word of the

preamble and remains asserted while all words to be transmitted are presented on the receive

data bus. TX_EN must be negated prior to the first rising edge of GTX_CLK following the final

word of a frame.

TX_ER

22

I§

Transmit error coding. When TX_ER and TX_EN are high, indicates that the transceiver

generates an error somewhere in the frame presently being transferred. When TX_ER is

asserted and TX_EN is deasserted, indicates the protocol device is presenting carrier extension

data. When TX_ER is deasserted with TX_EN asserted, indicates that normal data is being

presented.

VDD

1, 9,

23, 38,

48

Digital logic power. Provides power for all digital circuitry and digital I/O buffers.

VDDA

55, 57

Analog power. VDDA provides a supply reference for the high-speed analog circuits, receiver and

transmitter

† Low during power-on reset.

‡ High-impedance during power-on reset

§ Internal pulldown