S29GL01GS datasheet(35/104 Pages) SPANSION

35 / 104 page

December 21, 2012 S29GL_128S_01GS_00_07

GL-S MirrorBit® Family

Data

She e t

5.3.6

ASO Entry and Exit

5.3.6.1

ID-CFI ASO

The system can access the ID-CFI ASO by issuing the ID-CFI Entry command sequence during Read Mode.

This entry command uses the Sector Address (SA) in the command to determine which sector will be overlaid

and which sector's protection state is reported in word location 2h. See the detail description Table 6.2

on page 60.

The ID-CFI ASO allows the following activities:

 Read ID-CFI ASO, using the same SA as used in the entry command.

 Read Sector Protection State at Sector Address (SA) + 2h. Location 2h provides volatile information on the

current state of sector protection for the sector addressed. Bit 0 of the word at location 2h shows the logical

NAND of the PPB and DYB bits related to the addressed sector such that if the sector is protected by either

the PPB=0 or the DYB=0 bit for that sector the state shown is protected. (1= Sector protected, 0= Sector

unprotected). This protection state is shown only for the SA selected when entering ID-CFI ASO. Reading

other SA provides undefined data. To read a different SA protection state ASO exit command must be used

and then enter ID-CFI ASO again with the new SA.

 ASO Exit.

The following is a C source code example of using the CFI Entry and Exit functions. Refer to the Spansion

Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion flash

memory software development guidelines.

/* Example: CFI Entry command */

*( (UINT16 *)base_addr + 0x55 ) = 0x0098; /* write CFI entry command */

/* Example: CFI Exit command */

*( (UINT16 *)base_addr + 0x000 ) = 0x00F0; /* write cfi exit command */

5.3.6.2

Status Register ASO

The Status Register ASO contains a single word of registered volatile status for Embedded Algorithms. When

the Status Register read command is issued, the current status is captured (by the rising edge of WE#) into

the register and the ASO is entered. The Status Register content appears on all word locations. The first read

access exits the Status Register ASO (with the rising edge of CE# or OE#) and returns to the address space

map in use when the Status Register read command was issued. Write commands will not exit the Status

5.3.6.3

Secure Silicon Region ASO

The system can access the Secure Silicon Region by issuing the Secure Silicon Region Entry command

sequence during Read Mode. This entry command uses the Sector Address (SA) in the command to

determine which sector will be overlaid.

The Secure Silicon Region ASO allows the following activities:

 Read Secure Silicon Regions.

 Programming the customer Secure Silicon Region is allowed using the Word or Write Buffer Programming

commands.

 ASO Exit using legacy Secure Silicon Exit command for backward software compatibility.

 ASO Exit using the common exit command for all ASO - alternative for a consistent exit method.

S29GL01GS датащи(PDF) 35 Page - SPANSION

S29GL01GS датащи(HTML) 35 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL