SSM2404P datasheet(2/8 Pages) AD

2 / 8 page

REV. B

–2–

SSM2404–SPECIFICATIONS

(VS =

12 V, TA = +25 C, unless otherwise noted.

Typical specifications apply at TA = +25 C.)

Parameter

Symbol

Conditions

Min

Typ

Max

Units

AUDIO PERFORMANCE

Total Harmonic Distortion Plus Noise

THD+N

@ 1 kHz, with 80 kHz Filter,

RL = 100 kΩ, VIN = 2 V rms

0.0008

Spectral Noise Density

20 Hz to 20 kHz

0.8

nV/

√Hz

Wideband Noise Density

en p-p

20 Hz to 20 kHz

0.6

µV p-p

ANALOG SIGNAL SECTION

Analog Voltage Range

VINH = 2.4 V, IA = ± 2 mA

±12

Analog Current Range

VINH = 2.4 V, VA = 0 V

±10

ON Resistance

RON

IA = ± 10 mA, VA = ± 10 V dc

Ω

RON Matching

RON Match

IA = ± 10 mA, VA = 0 V

ON Leakage Current

IS(ON)

VA = ± 10 V

–20

0.1

+20

OFF Leakage Current

IS(OFF)

VA = ± 10 V

–20

0.1

+20

Charge Injection

ON-State Input Capacitance

CON

VA = 5 V rms

OFF-State Input Capacitance

COFF

VA = 5 V rms

OFF Isolation

ISO(OFF)

VA = 50 mV rms, f = 1 kHz, RL = 10 kΩ

–100

Channel-to-Channel Crosstalk

VA = 50 mV rms, f = 1 kHz, RL = 10 kΩ

–94

CONTROL SECTION

Digital Input High

VINH

DGND = 0 V

2.4

Digital Input Low

VINL

DGND = 0 V

0.8

Turn-On Time

tON

See Test Circuit

Turn-Off Time

tOFF

See Test Circuit

Break-Before-Make Time Delay

tON-tOFF

320

Logic Input Current

Logic HI

VINH = 2.4 V

–1000 1.3

+1000

Logic LO

VINL = 0.8 V

–1000 1.0

+1000

POWER SUPPLY

Supply Voltage Range

Single Supply

+11

+24

Dual Supply

±5.5

±12

Positive Supply Current

ISY+

All Channels On

0.9

Negative Supply Current

ISY–

All Channels On

–1.5

–0.6

Ground Current

All Channels On

–2.0

–0.3

NOTES

1Turn-on time is measured from the time the logic input reaches the 50% point to the time the output reaches 50% of the final value.

2Turn-off time is measured from the time the logic input reaches the 50% point to the time the output reaches 50% of the initial value.

Specifications subject to change without notice.

ABSOLUTE MAXIMUM RATINGS

Supply Voltage

Single Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +27 V

Dual Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±13.5 V

Analog Input Voltage (VA) . . . . . . . . . . . . . . . . . . . . . . . . . . VS

Logic Input Voltage (VINL/INH) . . . . . . . . . . . . . . . . . . . . . . VS

Maximum Current Through Any Switch . . . . . . . . . . . 20 mA

Operating Temperature Range . . . . . . . . . . . . –40

°C to +85°C

Storage Temperature Range . . . . . . . . . . . . –65

°C to +150°C

Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . +150

°C

Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . +300

°C

Thermal Resistance1

20-Pin Plastic DIP (P):

JA = 74,

JC = 32

. . . . . . . . .

°C/W

20-Pin SOIC (S):

JA = 90,

JC = 27 . . . . . . . . . . . . . .

°C/W

NOTE

JA is specified for worst case mounting conditions, i.e., θJA is specified for device

in socket for P-DIP package.

ORDERING GUIDE

Operating

Temperature

Package

Model

Range

Package

Option*

SSM2404P

–40

°C to +85°C 20-Pin Plastic DIP N-20

SSM2404S

–40

°C to +85°C 20-Pin SOIC

R-20

*N = Plastic DIP, R = SOIC.

SSM2404P датащи(PDF) 2 Page - Analog Devices

SSM2404P датащи(HTML) 2 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8

датащи скачать

ссылки URL