| поискавой системы для электроныых деталей |
|
CINT1175 датащи(PDF) 2 Page - SL Power Electronics |
|
|
|||||||||||||||||||||||||||||
CINT1175 датащи(HTML) 2 Page - SL Power Electronics |
|
2 / 8 page ![]() CINT1175 175W Single Output Industrial Series www.slpower.com CINT1175 REV 5.4, 17-DEC-12 2 General Specifications (continued) Input Fuses F1, F2: 4A, 250Vac fuses provided on all models Overload Protection Hiccup Mode Earth Leakage Current <750μA@264Vac, 60Hz, NC Short Circuit Protection Provided - no damage will occur if the output is shorted. Efficiency 90% typical at 115Vac Overvoltage Protection OVP firing reduces output voltage to <50% of nominal in <50ms. See chart for trip range. Output Power 175W continuous, with 200 lfm airflow, 120W convection cooled – See chart for specific voltage model ratings. Switching Frequency PFC: Fixed, 65kHz Main Converter: Variable 35-200kHz, 65- 70kHz at full load. Transient Response 50% load step. i/t: <0.2A/μS Max Volt Deviation = 3% Isolation Input-Output: 4000Vac Input-Ground: 1800Vac Output-Ground: 1500Vac Ripple and Noise See chart Operating Temperature -10°C to +70°C Start Up at -40°C, full load Output Voltage See chart Temperature Derating Derate output power linearly above 50°C to 50% at 70°C Voltage Adjustability +/-5% from nominal Storage Temperature -40°C to +85°C Minimum Load Not required Altitude Operating: -500 to 10,000 ft. Non-operating: -500 to 40,000 ft. Total Regulation +/- 3%. See chart Relative Humidity 5% to 95%, non-condensing Vibration Operating: 0.003g/Hz, 1.5grms overall, 3 axes, 10 min/axis Non-Operating: 0.026g2/Hz, 5.0grms overall, 3 axes, 1 hr/axis Shock Operating: Half-sine, 20gpk, 10ms, 3 axes, 6 shocks total Non-Operating: Half-sine, 40 gpk, 10 ms, 3 axes, 6 shocks total Dimensions W: 2.0” x L: 4.0” x H: 1.3” Safety Standards EN/CSA/UL/IEC 60950-1, 2nd Edition Weight 210g MTBF 331,105 hours, 175W load, 110Vac input, 25 °C ambient Auxiliary Signals AC Power Fail: During normal operations, stays HIGH. Signal goes LOW with 5mS warning before loss of DC output from AC failure. DC OK: Open collector logic signal goes and stays HIGH 100mS to 500mS after main output reaches regulation. Inhibit: Connect to inhibit pin to output common to inhibit the DC output. |
|
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |