ADV7195 datasheet(21/36 Pages) AD

21 / 36 page

REV. A

ADV7195

–21–

FILTER GAIN

FG (FG7–FG0)

(Address (SR4–SR0) = 10H)

Figure 34 shows the various operations under the control of the

Filter Gain register.

FG6

FG5

FG3

FG1

FG4

FG2

FG0

FG7

FG7–FG4

FILTER GAIN B

0 0 0 0

0 0 0 1

0 0 1 0

0 0 1 1

0 1 0 0

0 1 0 1

0 1 1 0

0 1 1 1

1 0 0 0

–8

1 0 0 1

–7

1 0 1 0

–6

1 0 1 1

–5

1 1 0 0

–4

1 1 0 1

–3

1 1 1 0

–2

1 1 1 1

–1

FG3–FG0

FILTER GAIN A

0 0 0 0

0 0 0 1

0 0 1 0

0 0 1 1

0 1 0 0

0 1 0 1

0 1 1 0

0 1 1 1

1 0 0 0

–8

1 0 0 1

–7

1 0 1 0

–6

1 0 1 1

–5

1 1 0 0

–4

1 1 0 1

–3

1 1 1 0

–2

1 1 1 1

–1

Figure 34. Filter Gain Register

FG BIT DESCRIPTION

Filter Gain A (FG3–FG0)

These bits are used to program the gain A value, which varies

from response –8 to response +7 and are applied to Filter A.

Filter Gain B (FG4–FG7)

These bits are used to program the gain B value, which varies

from response –8 to response +7, and are applied to Filter B.

Refer to Sharpness Filter Control and Adaptive Filter Control

section for more detail.

GAMMA CORRECTION REGISTERS 0–13

(GAMMA CORRECTION 0–13)

(Address (SR5–SR0) = 14H–21H)

The Gamma Correction Registers are 14 8-bit-wide registers.

They are used to program the gamma correction Curves A and B.

Generally, gamma correction is applied to compensate for the

nonlinear relationship between signal input and brightness

level output (as perceived on the CRT). It can also be applied

wherever nonlinear processing is used.

Gamma correction uses the function:

SignalOUT = (Signal IN)γ

where

γ = gamma power factor.

Gamma correction is performed on the luma data only.

The user has the choice of two different curves, Curve A or

Curve B. At any one time only one of these curves can be used.

The response of the curve is programmed at seven predefined

locations. In changing the values at these locations the gamma

curve can be modified. Between these points linear interpola-

tion is used to generate intermediate values. Considering the

curve to have a total length of 256 points, the seven locations

are at: 32, 64, 96, 128, 160, 192, 224.

Locations 0, 16, 240, and 255 are fixed and cannot be changed.

For the length of 16 to 240 the gamma correction curve has to

be calculated as below:

y = xγ

where

y = gamma corrected output.

x = linear input signal.

γ = gamma power factor.

To program the gamma correction registers, the seven values

for y have to be calculated using the following formula:

yn = [x(n–16)/(240 – 16)]γ

× (240–16) + 16

where

x(n–16) = Value for x along x-axis at points:

= 32, 64, 96, 128, 160, 192, or 224.

= Value for y along the y-axis, which has to be written

into the gamma correction register.

Example:

y32 = [(16/224)

0.5

× 2 24] + 16 = 76*

y64 = [(48/224)

0.5

× 224] + 16 =120*

y96 = [(80/224)

0.5

× 224] + 16 = 150*

y128 = [(112/224)

0.5

× 224] + 16 = 174*

*Rounded to the nearest integer.

The above will result in a gamma curve shown on the next

page, assuming a ramp signal as an input.

250

200

150

100

300

SIGNAL OUTPUT

SIGNAL INPUT

0.5

GAMMA CORRECTION BLOCK OUTPUT

TO A RAMP INPUT

100

150

200

250

LOCATION

Figure 35. Signal Input (Ramp) and Signal Output for

Gamma 0.5

ADV7195 датащи(PDF) 21 Page - Analog Devices

ADV7195 датащи(HTML) 21 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

датащи скачать

ссылки URL