ADMCF341 datasheet(8/36 Pages) AD

8 / 36 page

REV. 0

–8–

ADMCF341

The processor contains three independent computational units:

the arithmetic and logic unit (ALU), the multiplier/accumulator

(MAC), and the shifter. The computational units process 16-bit

data directly and have provisions to support multiprecision

computations. The ALU performs a standard set of arithmetic

and logic operations as well as provides support for division

primitives. The MAC performs single-cycle multiply, multiply/add,

and multiply/subtract operations with 40 bits of accumulation.

The shifter performs logical and arithmetic shifts, normalization,

denormalization, and derive-exponent operations. The shifter

can be used to efficiently implement numeric format control,

including floating-point representations. The internal result (R)

bus directly connects the computational units so that the output

of any unit may be the input of any unit on the next cycle.

A powerful program sequencer and two dedicated data address

generators ensure efficient delivery of operands to these compu-

tational units. The sequencer supports conditional jumps and

subroutine calls and returns in a single cycle. With internal loop

counters and loop stacks, the ADMCF341 executes looped code

with zero overhead; no explicit jump instructions are required to

maintain the loop.

Two data address generators (DAGs) provide addresses for

simultaneous dual operand fetches from data memory and pro-

gram memory. Each DAG maintains and updates four address

pointers (I registers). Whenever the pointer is used to access

data (indirect addressing), it is post-modified by the value in

one of four modifications (M registers). A length value may be

associated with each pointer (L registers) to implement auto-

matic modulo addressing for circular buffers. The circular

buffering feature is also used by the serial ports for automatic

data transfers to and from on-chip memory. DAG1 generates

only data memory addresses and provides an optional bit-reversal

capability. DAG2 may generate either program or data memory

addresses but has no bit-reversal capability. Efficient data trans-

fer is achieved with the use of five internal buses:

∑ Program memory address (PMA) bus

∑ Program memory data (PMD) bus

∑ Data memory address (DMA) bus

∑ Data memory data (DMD) bus

∑ Result (R) bus

Program memory can store both instructions and data, permit-

ting the ADMCF341 to fetch two operands in a single cycle—

one from program memory and one from data memory. The

ADMCF341 can fetch an operand from on-chip program

memory and the next instruction in the same cycle. The

ADMCF341 writes data from its 16-bit registers to the 24-bit

program memory using the PX register to provide the lower 8

bits. When it reads data (not instructions) from 24-bit program

memory to a 16-bit data register, the lower 8 bits are placed in

the PX register.

The ADMCF341 can respond to a number of distinct DSP

core and peripheral interrupts. The DSP interrupts comprise a

serial port receive interrupt, a serial port transmit interrupt, a

timer interrupt, and two software interrupts. Additionally, the

motor control peripherals include two PWM interrupts and a

PIO interrupt.

Serial port 0 (SPORT0) provides a complete synchronous serial

interface with optional companding in hardware and a wide

variety of framed and unframed data transmit and receive

modes of operation. Serial port 1 (SPORT1) is available with a

limited number of I/Os. It is mainly intended for codebooting to

serial ROMs (SROM) and support of the debugging tools.

SPORT0 and SPORT1 can generate an internal programmable

serial clock or accept an external serial clock.

A programmable interval counter is also included in the DSP

core and can be used to generate periodic interrupts. A 16-bit

count register (TCOUNT) is decremented every n processor

cycles, where n – 1 is a scaling value stored in the 8-bit TSCALE

rupt is generated, and the count register is reloaded from a

16-bit period register (TPERIOD).

The ADMCF341 instruction set provides flexible data moves

and multifunction (one or two data moves with a computation)

instructions. Each instruction is executed in a single 50 ns

processor cycle (for a 10 MHz CLKIN). The ADMCF341

assembly language uses an algebraic syntax for ease of coding

and readability. A comprehensive set of development tools

supports program development. For further information on the

DSP core, refer to the ADSP-2100 Family User’s Manual, Third

Edition, with particular reference to the ADSP-2171.

SERIAL PORTS

The ADMCF341 incorporates two complete synchronous serial

ports (SPORT1 and SPORT0) for serial communication and

multiprocessor communication.

Following is a brief list of capabilities of the ADMCF341

SPORTs. Refer to the ADSP-2100 Family User’s Manual, Third

Edition, for further details.

∑ SPORTs are bidirectional and have a separate, double-buff-

ered transmit and receive section.

∑ SPORTs use an external serial clock or generate their own

serial clock internally.

∑ SPORTs have independent framing for the receive and

transmit sections. Sections run in a frameless mode or with

frame synchronization signals internally or externally gener-

ated. Frame synchronization signals are active high or

inverted, with either of two pulsewidths and timings.

∑ SPORTs support serial data word lengths from 3 bits to

16 bits and provides optional A-law and

m-law companding

according to ITU (formerly CCITT) recommendation

G.711.

∑ SPORT receive and transmit sections can generate unique

interrupts on completing a data word transfer.

∑ SPORTs can receive and transmit an entire circular buffer

of data with only one overhead cycle per data word. An

interrupt is generated after a data buffer transfer.

∑ SPORT0 has a multichannel interface to selectively receive

and transmit a 24-word, or 32-word, timedivision multi-

plexed, serial bitstream.

∑ SPORT0 can be configured as an SPI port (master mode

only). The clock phase and polarity are programmable

through the MODECTRL register.

∑ SPORT1 is the default port for program/data memory boot

loading and for development tools interface. The DT1/FL1

pin can be configured as SROM/E

2PROM reset signal.

ADMCF341 датащи(PDF) 8 Page - Analog Devices

ADMCF341 датащи(HTML) 8 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

датащи скачать

ссылки URL