AT91SAM datasheet(38/67 Pages) ATMEL

38 / 67 page

11100BS–ATARM–31-Jul-12

SAM4S Series [Preliminary]

9.1.3.9

Fast Flash Programming Interface

The Fast Flash Programming Interface allows programming the device through a multiplexed

fully-handshaked parallel port. It allows gang programming with market-standard industrial

programmers.

The FFPI supports read, page program, page erase, full erase, lock, unlock and protect

commands.

9.1.3.10

SAM-BA Boot

The SAM-BA Boot is a default Boot Program which provides an easy way to program in-situ the

on-chip Flash memory.

The SAM-BA Boot Assistant supports serial communication via the UART and USB.

The SAM-BA Boot provides an interface with SAM-BA Graphic User Interface (GUI).

The SAM-BA Boot is in ROM and is mapped in Flash at address 0x0 when GPNVM bit 1 is set to 0.

9.1.3.11

GPNVM Bits

The SAM4S features two GPNVM bits. These bits can be cleared or set respectively through the

commands “Clear GPNVM Bit” and “Set GPNVM Bit” of the EEFC User Interface.

The Flash of the SAM4S16/SA16 is composed of 1024 Kbytes in a single bank. The Flash of the

SAM4S8 is composed of 512Kbytes in a single bank.

The SAM4SD32/SD16 features 3 GPNVM bits that can be cleared or set respectively through

the "Clear GPNVM Bit" and "Set GPNVM Bit" commands of the EEFC User Interface. The

GPNVM0 is the security bit. The GPNVM1 is used to select the boot mode (boot always at 0x00)

on ROM or FLASH. The SAM4SD32/16 embeds an additional GPNVM bit: GPNVM2. This

GPNVM bit is used only to swap the Flash0 and Flash1. If GPNVM bit 2 is:

ENABLE: the Flash1 is mapped at address 0x0040_0000 (Flash1 and Flash0 are continuous).

DISABLE: the Flash0 is mapped at address 0x0040_0000 (Flash0 and Flash1 are continuous).

9.1.4

Boot Strategies

The system always boots at address 0x0. To ensure maximum boot possibilities, the memory

layout can be changed via GPNVM.

A general purpose NVM (GPNVM) bit is used to boot either on the ROM (default) or from the

Flash.

The GPNVM bit can be cleared or set respectively through the commands “Clear General-pur-

pose NVM Bit” and “Set General-purpose NVM Bit” of the EEFC User Interface.

Setting GPNVM Bit 1 selects the boot from the Flash, clearing it selects the boot from the ROM.

Asserting ERASE clears the GPNVM Bit 1 and thus selects the boot from the ROM by default.

Table 9-2.

General-purpose Non volatile Memory Bits

GPNVMBit[#]

Function

Security bit

Boot mode selection

Flash selection (Flash 0 or Flash 1)

AT91SAM датащи(PDF) 38 Page - ATMEL Corporation

AT91SAM датащи(HTML) 38 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

датащи скачать

ссылки URL