| поискавой системы для электроныых деталей |
|
RT5002 датащи(PDF) 5 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT5002 датащи(HTML) 5 Page - Richtek Technology Corporation |
|
5 / 40 page ![]() RT5002 5 DS5002-00 November 2011 www.richtek.com Functional Pin Description Pin No. Pin Name Pin Function 1 INT Interrupt Indicator Open Drain Output. If any toggle events of TS_FAULT, PGOOD, EOC, or SAFE happen, the output INT goes low. After I 2 C register bank address 0x2 is read or power on reset, INT goes high. 2 FB1 Feedback Input of CH1. 3 VDDM IC Analog Power Pin. 4 FB7 Feedback Input of CH7 in Step-Up Mode or Current Sink Pin of CH7 in Current Source Mode. 5 PVD7 Power Output of CH7 6 LX7 Switch Node of CH7 in Step-Up Mode. 7 BATS Output pin of voltage divider for battery voltage level sensing enabled after CH2 soft-start end. BATS voltage is about 60% of BAT. 8 LX4 Switch Node of CH4. 9 PVD4 Power Input of CH4. 10 FB4 Feedback Input of CH4. 11 ISETA Charge Current Set Input. Connect a resistor (RISETA) between ISETA and GND. 12 TS Temperature Sense Input. The TS pin connects to a battery’s thermistor to determine whether the battery is too hot or too cold to be charged. If the battery’s temperature is out of range, charging is paused until it re-enters the valid range. TS also detects whether the battery (with NTC) is present or not. 13 VP Power Output of 3.3V Buffer for Battery Temperature Sensing. 14 SDA Data Signal Pin of I 2 C Interface. 15 SCL Clock Signal Pin of I 2 C Interface. 16 PVD6 Power Input of CH6. 17 LX6 Switch Node of CH6. 18 VOUT6 Sense Input of CH6 Inverting Output Node. 19 FB6 Feedback Input of CH6. 20 VREF 1.8V Reference Output. 21 FB3 Feedback Input of CH3. 22 PVD3 Power Input of CH3. 23 LX3 Switch Node of CH3. 24 EN1234 Enable Pin of CH1, CH2, CH3, and CH4. 25 FB5 Feedback Input of CH5. 26 PVD5 Power Output of CH5. 27 LX5 Switch Node of CH5. 28 TSSEL Input Pin to Select Temperature Sensing Thresholds. Thresholds of TSSEL = H are 60% and 38% of VP voltage. Thresholds of TSSEL = L are 74% and 28% of VP voltage. 29 FB2 Feedback Input of CH2. 30 WAKE Wake-Up Impulse Push-Pull Output. If VIN or BAT plug in, WAKE pin generates one 55ms width high pulse to notify micro processor. 31 LX2 Switch Node of CH2. 32 PVD2 Power Input of CH2. To be continued |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |