PS219B2-AS datasheet(3/13 Pages) MITSUBISHI

3 / 13 page

< Dual-In-Line Package Intelligent Power Module >

PS219B2-S/-AS/-CS/-ST/-AST/-CST

TRANSFER MOLDING TYPE

INSULATED TYPE

Publication Date : November 2011

ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted)

INVERTER PART

Limits

Symbol

Parameter

Condition

Min.

Typ.

Max.

Unit

Tj= 25°C

1.50

2.00

VCE(sat)

Collector-emitter saturation

voltage

VD=VDB = 15V, VIN= 5V, IC= 5A

Tj= 125°C

1.60

2.10

VEC

FWDi forward voltage

VIN= 0V, -IC= 5A

1.70

2.20

ton

0.75

1.35

1.95

μs

tC(on)

0.35

0.55

μs

toff

1.40

2.00

μs

tC(off)

0.30

0.60

μs

trr

Switching times

VCC= 300V, VD= VDB= 15V

IC= 5A, Tj= 125°C, VIN= 0

↔5V

Inductive Load (upper-lower arm)

0.30

μs

Tj= 25°C

ICES

Collector-emitter cut-off

current

VCE=VCES

Tj= 125°C

CONTROL (PROTECTION) PART

Limits

Symbol

Parameter

Condition

Min.

Typ.

Max.

Unit

VD=15V, VIN=0V

2.80

Total of VP1-VNC, VN1-VNC

VD=15V, VIN=5V

2.80

VD=VDB=15V, VIN=0V

0.10

IDB

Circuit current

Each part of VUFB-U,

VVFB-V, VWFB-W

VD=VDB=15V, VIN=5V

0.10

VSC(ref)

Short circuit trip level

VD = 15V

(Note 3)

0.43

0.48

0.53

UVDBt

Trip level

7.0

10.0

12.0

UVDBr

P-side Control supply

under-voltage protection(UV)

Reset level

7.0

10.0

12.0

UVDt

Trip level

10.3

12.5

UVDr

N-side Control supply

under-voltage protection(UV)

Tj ≤125°C

Reset level

10.8

13.0

LVIC Temperature=90

C

2.63

2.77

2.91

VOT

Temperature Output

(-S/-AS/-CS only)

Pull down R=5kΩ (Note 4)

LVIC Temperature=25

C

0.88

1.13

1.39

OTt

VD = 15V

Trip level

100

120

140

°C

OTrh

Overt temperature protection

(OT, -ST/-AST/-CST only) (Note5)

Detect LVIC temperature

Hysteresis of trip-reset

°C

VFOH

VSC = 0V, FO terminal pulled up to 5V by 10kΩ

4.9

VFOL

Fault output voltage

VSC = 1V, IFO = 1mA

0.95

tFO

Fault output pulse width

(Note 6)

μs

IIN

Input current

VIN = 5V

0.70

1.00

1.50

Vth(on)

ON threshold voltage

2.10

2.60

Vth(off)

OFF threshold voltage

0.80

1.30

Vth(hys)

ON/OFF threshold

hysteresis voltage

Applied between UP, VP, WP, UN, VN, WN-VNC

0.35

0.65

Bootstrap Di forward voltage

IF=10mA including voltage drop by limiting resistor

(Note 7)

1.1

1.7

2.3

Built-in limiting resistance

Included in bootstrap Di

100

120

Ω

Note 3 : SC protection works only for N-side IGBT. Please select the external shunt resistance such that the SC trip-level is less than 1.7 times of the current rating.

Note 4 : DIPIPM don't shutdown IGBTs and output fault signal automatically when temperature rises excessively. When temperature exceeds the protective level that

user defined, controller (MCU) should stop the DIPIPM. Temperature of LVIC vs. VOT output characteristics is described in Fig. 3.

5 : When the LVIC temperature exceeds OT trip temperature level(OTt), OT protection works and Fo outputs. In that case if the heat sink dropped off or fixed

loosely, don't reuse that DIPIPM. (There is a possibility that junction temperature of power chips exceeded maximum Tj(150

C).

6 : Fault signal Fo outputs when SC, UV or OT protection works. Fo pulse width is different for each protection modes. At SC failure, Fo pulse width is a fixed

width (=minimum 20μs), but at UV or OT failure, Fo outputs continuously until recovering from UV or OT state. (But minimum Fo pulse width is 20μs.)

7 : The characteristics of bootstrap Di is described in Fig.2.

Fig. 2 Characteristics of bootstrap Di VF-IF curve (@Ta=25C) including voltage drop by limiting resistor (Right chart is enlarged chart.)

100

120

140

160

0123456789 10 11 12 13 14 15

F [V]

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

F [V]

PS219B2-AS датащи(PDF) 3 Page - Mitsubishi Electric Semiconductor

PS219B2-AS датащи(HTML) 3 Page - Mitsubishi Electric Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

датащи скачать

ссылки URL