LTC4263 datasheet(14/32 Pages) LINER

14 / 32 page

LTC4270/LTC4271

42701fb

CPD (Pin 8): Clock Transceiver Positive Input Output

(Digital). Connect to CPA through a data transformer.

CND (Pin 9): Clock Transceiver Negative Input Output

(Digital). Connect to CNA through a data transformer.

DPD (Pin 10): Data Transceiver Positive Input Output

(Digital). Connect to DPA through a data transformer.

DND (Pin 11): Data Transceiver Negative Input Output

(Digital). Connect to DNA through a data transformer.

VDD33 (Pins 12, 20): VDD IO Power Supply. Connect to

a 3.3V power supply relative to DGND. VDD33 must be

bypassed to DGND near the LTC4271 with at least a 0.1μF

capacitor.

RESET(Pin14):ResetInput,ActiveLow.WhentheRESET

pin is low, the LTC4270/LTC4271 is held inactive with all

ports off and all internal registers reset to their power-up

states. When RESET is pulled high, the LTC4271 begins

normal operation. RESET can be connected to an external

capacitor or RC network to provide a power turn-on delay.

Internal filtering of the RESET pin prevents glitches less

than 1μs wide from resetting the LTC4270/LTC4271.

Internally pulled up to VDD.

INT (Pin 15): Interrupt Output, Open Drain. INT will pull

low when any one of several events occur in the LTC4271.

It will return to a high impedance state when bits 6 or 7

are set in the Reset PB register (1Ah). The INT signal can

be used to generate an interrupt to the host processor,

eliminating the need for continuous software polling. In-

dividual INT events can be disabled using the INT Mask

documentation for more information. The INT pin is only

updated between I2C transactions.

SDAOUT (Pin 16): Serial Data Output, Open Drain Data

Output for the I2C Serial Interface Bus. The LTC4271 uses

two pins to implement the bidirectional SDA function to

simplify optoisolation of the I2C bus. To implement a stan-

dardbidirectionalSDApin,tieSDAOUTandSDAINtogether.

See Applications Information for more information.

SDAIN (Pin 17): Serial Data Input. High impedance data

inputfortheI2Cserialinterfacebus.TheLTC4271usestwo

pinstoimplementthebidirectionalSDAfunctiontosimplify

optoisolation of the I2C bus. To implement a standard

bidirectional SDA pin, tie SDAOUT and SDAIN together.

See Applications Information for more information.

SCL (Pin 18): Serial Clock Input. High impedance clock

input for the I2C serial interface bus. The SCL pin should

be connected directly to the I2C SCL bus line. SCL must

be tied high if the I2C serial interface bus is not used.

CAP1(Pin19):CorePowerSupplyBypassCapacitor.Con-

nect a 1µF Bypass capacitance to DGND for the internal

1.8V regulator. Do not use other capacitor values.

AUTO (Pin 21): AUTO Pin Mode Input. AUTO pin mode

allows the LTC4271 to detect and power up a PD even if

there is no host controller present on the I2C bus. The

AUTO pin determines the state of the internal registers

when the LTC4271 is reset or comes out of VDD UVLO

(seeLTC4271SoftwareProgrammingdocumentation).The

states of these register bits can subsequently be changed

via the I2C interface. Internally pulled down to DGND. Must

be tied locally to either VDD or DGND.

GP1 (Pin 22): General Purpose Digital Input Output for

customer applications. Referenced to DGND.

GP0 (Pin 23): General Purpose Digital Input Output for

customer applications. Referenced to DGND.

MSD (Pin 24): Maskable Shutdown Input. Active low.

When pulled low, all ports that have their corresponding

mask bit set in the mconfig register (17h) will be reset.

Internal filtering of the MSD pin prevents glitches less

than 1μs wide from resetting ports. The MSD Pin Mode

pulled up to VDD.

DGND(ExposedPadPin25):DigitalGround.DGNDshould

be connected to the return from the VDD supply.

pin Functions

LTC4263 датащи(PDF) 14 Page - Linear Technology

LTC4263 датащи(HTML) 14 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

датащи скачать

ссылки URL