AP7362 datasheet(4/13 Pages) DIODES

4 / 13 page

AP7362

1.5A, LOW QUIESCENT CURRENT, FAST TRANSIENT

ULTRA-LOW DROPOUT LINEAR REGULATOR

AP7362

Document number: DS35058 Rev. 2 - 2

4 of 13

www.diodes.com

June 2011

Electrical Characteristics

TA = 25

oC, V

IN = 3.3V, VOUT =1.8V, IOUT = 10mA, VEN = VIN, CIN = 10μF, COUT = 10μF, VEN = 2V, unless otherwise stated.

Minimum and maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely

parametric norm at TA = 25

oC, and are provided for reference purposes only.

Symbol

Parameter

Test Conditions

Min

Typ.

Max

Unit

VADJ

ADJ Pin Voltage

VIN = VIN-Min to VIN-Max,

IOUT= 10mA to 1.5A

TA = 25

0.584 0.605 0.626

Over temp

0.575

0.635

VADJ

ADJ Pin Voltage (A Grade)

VIN = VIN-Min to VIN-Max,

IOUT= 10mA to 1.5A

TA = 25

0.596 0.605 0.614

Over temp

0.587

0.623

IADJ

ADJ Pin Bias Current

VIN = VIN-Min to VIN-Max

TA = 25

Over temp

750

VDropout

Dropout Voltage (Note 4)

IOUT = 1.5A, VOUT = 2.5V

TA = 25

190

240

Over temp

280

ΔVOUT /ΔVIN Line Regulation (Note 5)

VIN = VIN-Min to VIN-Max

TA = 25

0.04

%/V

Over temp

0.05

ΔVOUT /ΔIOUT Load Regulation (Note 5)

IOUT = 10mA to 1.5A

TA = 25

0.18

%/A

Over temp

0.33

IGND

Ground Pin Current in Normal

Operation Mode

IOUT = 10mA to 1.5A

TA = 25

1.2

Over temp

1.3

ISHDN

Ground Pin Current

VEN < VIL

TA = 25

0.025 0.125

μA

Over temp

IOUT-PK

Peak Output Current

VOUT

≥ VOUT-NOM -5%

3.6

ISC

Short Circuit Current

OUT grounded

TA = 25

3.7

Over temp

VIH

Enable Logic High

VIN = VIN-Min to VIN-Max

Over temp

1.4

VIL

Enable Logic Low

VIN = VIN-Min to VIN-Max

Over temp

0.65

IIH

Enable Pin High Current

VEN = VIN

IIL

Enable Pin Low Current

VEN = 0V

0.1

td(off)

Turn-off delay

From VEN < VIL to VOUT = OFF,

IOUT = 1.5A

μs

td(on)

Turn-on delay

From VEN > VIH to VOUT = ON,

IOUT = 1.5A

μs

PSRR

Ripple Rejection

VIN = 3.0V, IOUT = 1.5A, f = 120Hz

VIN = 3.0V, IOUT = 1.5A, f = 1kHz

ρn(l/f)

Output Noise Density

F = 120Hz, COUT = 10μF ceramic

1.0

μV/

√Hz

Output Noise Voltage

BW = 100Hz – 100kHz,

COUT = 10μF ceramic

μV(rms)

TSHDN

Thermal shutdown threshold

TJ rising

170

°C

THYS

Thermal shutdown hysteresis

TJ falling from TSHDN

θJA

Thermal Resistance Junction-to-

Ambient

U-DFN2030-8 (Note 6)

174.0

oC/W

SO-8EP (Note 6)

52.8

θJC

Thermal Resistance Junction-to-

Case

U-DFN2030-8 (Note 6)

28.2

oC/W

SO-8EP (Note 6)

10.0

Notes:

4. Dropout voltage is the minimum voltage difference between the input and the output at which the output voltage drops 2% below its nominal value.

For any output voltage less than 2.5V, the minimum VIN operating voltage is the limiting factor.

5. The line and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the adjust

voltage tolerance specification.

6. Device mounted on 2” x 2” FR-4 substrate PCB, 2oz copper with minimum recommended pad layout.

AP7362 датащи(PDF) 4 Page - Diodes Incorporated

AP7362 датащи(HTML) 4 Page - Diodes Incorporated

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

датащи скачать

ссылки URL