| поискавой системы для электроныых деталей |
|
FSK датащи(PDF) 10 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
FSK датащи(HTML) 10 Page - ATMEL Corporation |
|
10 / 13 page ![]() 10 4546F–RKE–12/08 T5750 Output power variation for the full temperature range Tamb = –40°C to +85°C, V S = 3.0V VS = 2.0V ΔP Ref ΔP Ref –1.5 –4.0 dB dB Output power variation for the full temperature range Tamb = –40°C to +125°C, V S = 3.0V V S = 2.0V, POut = PRef + ΔPRef ΔP Ref ΔP Ref –2.0 –4.5 dB dB Achievable output-power range Selectable by load impedance POut_typ –3 +5.5 dBm Spurious emission fCLK = f0/128 Load capacitance at pin CLK = 10 pF f O ±1 × fCLK fO ±4 × fCLK other spurious are lower –52 –52 dBc dBc Oscillator frequency XTO (= phase comparator frequency) f XTO = f0/64 f XTAL = resonant frequency of the XTAL, CM ≤ 10 fF, load capacitance selected accordingly T amb = –40°C to +85°C, Tamb = –40°C to +125°C f XTO –30 –40 f XTAL +30 +40 ppm ppm PLL loop bandwidth 250 kHz Phase noise of phase comparator Referred to fPC = fXT0, 25 kHz distance to carrier –116 –110 dBc/Hz In loop phase noise PLL 25 kHz distance to carrier –80 –74 dBc/Hz Phase noise VCO at 1 MHz at 36 MHz –89 –120 –86 –117 dBc/Hz dBc/Hz Frequency range of VCO fVCO 868 928 MHz Clock output frequency (CMOS microcontroller compatible) f 0/256 MHz Voltage swing at pin CLK CLoad ≤ 10 pF V0h V 0l VS × 0.8 V S × 0.2 V V Series resonance R of the crystal Rs 110 Ω Capacitive load at pin XT0 7pF FSK modulation frequency rate Duty cycle of the modulation signal = 50% 0 32 kHz ASK modulation frequency rate Duty cycle of the modulation signal = 50% 0 32 kHz ENABLE input Low level input voltage High level input voltage Input current high V Il VIh IIn 1.7 0.25 20 V V µA PA_ENABLE input Low level input voltage High level input voltage Input current high VIl V Ih IIn 1.7 0.25 V S (1) 5 V V µA 7. Electrical Characteristics (Continued) VS = 2.0V to 4.0V, Tamb = –40°C to 125°C unless otherwise specified. Typical values are given at VS = 3.0V and Tamb = 25°C. All parameters are referred to GND (pin 7). Parameters Test Conditions Symbol Min. Typ. Max. Unit Note: 1. If VS is higher than 3.6V, the maximum voltage will be reduced to 3.6V. |
|
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |