AP393 datasheet(10/15 Pages) DIODES

10 / 15 page

AP393

LOW POWER LOW OFFSET VOLTAGE DUAL

COMPARATORS

AP393

Document number: DS31006 Rev. 8 - 2

10 of 15

www.diodes.com

July 2010

Electrical Characteristics (Continued)

(VCC = 5V) (Note 5)

Symbol

Parameter

Conditions

Min

Typ.

Max

Unit

VOFFSET

Input Offset Voltage

(Note 10)

IOFFSET

Input Offset Current

IIN(+) -IIN(-), VCM = 0V

150

IBIAS

Input Bias Current

IIN(+) or IIN(-) with Output In

Linear Range, VCM = 0V

(Note 6)

400

Input Common Mode Voltage

Range

+ =30V (Note 7)

+ -2.0

VSAT

Saturation Voltage

VIN(-) = 1V, VIN(+) = 0,

ISINK < 4mA

700

IO(Leak)

Output Leakage Current

VIN(-) = 0, VIN(+) = 1V,

VO = 30V

1.0

μA

Differential Input Voltage

Keep All VIN’s > 0V (or V

-, if

Used), (Note 9)

Notes:

2. For operating at high temperatures, the AP393 must be derated based on a 125°C maximum junction temperature and a

thermal resistance of 170°C/W which applies for the device soldered in a printed circuit board, operating in a still air

ambient.The low bias dissipation and the “ON-OFF” characteristic of the outputs keeps the chip dissipation very small.

(PD<100mW), provided the output transistors are allowed to saturate

3. Short circuits from the output to V

+ can cause excessive heating and eventual destruction. When considering short circuits to

ground, the maximum output current is approximately 20mA independent of the magnitude of V

4. This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base

junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this

diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output

voltages of the comparators to go to the V

+ voltage level (or to ground for a large overdrive) for the time duration that an input

is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which is negative,

again returns to a value greater than -0.3V.

5. The AP393 temperature specifications are limited to 0°C < TOP < +70°C.

6. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of

the state of the output so no loading change exists on the reference or input lines.

7. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The

upper end of the common-mode voltage range is V

+-1.5V at 25°C, but either or both inputs can go to 36V without damage,

independent of the magnitude of V

8. The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals 300ns can be obtained,

see typical performance characteristics section.

9. Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the

common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than -0.3V

(or 0.3V below the magnitude of the negative power supply, if used).

10. At output switch point, VO ~ 1.4V, RS=0Ω with V

+ from 5V to 30V; and over the full input common-mode range (0V to V+-1.5V),

at 25°C.

AP393 датащи(PDF) 10 Page - Diodes Incorporated

AP393 датащи(HTML) 10 Page - Diodes Incorporated

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

датащи скачать

ссылки URL