ST10F272Z2T3 datasheet(147/189 Pages) STMICROELECTRONICS

147 / 189 page

ST10F272Z2

Electrical characteristics

147/189

‘LSB’ has a value of VAREF/1024.

For Port5 channels, the specified TUE (± 2LSB) is guaranteed also with an overload condition (see IOV

specification) occurring on maximum 2 not selected analog input pins of Port5 and the absolute sum of

input overload currents on all Port5 analog input pins does not exceed 10 mA.

For Port1 channels, the specified TUE is guaranteed when no overload condition is applied to Port1 pins:

when an overload condition occurs on maximum 2 not selected analog input pins of Port1 and the input

positive overload current on all analog input pins does not exceed 10 mA (either dynamic or static

injection), the specified TUE is degraded (± 7LSB). To get the same accuracy, the negative injection

current on Port1 pins shall not exceed -1mA in case of both dynamic and static injection.

The coupling factor is measured on a channel while an overload condition occurs on the adjacent not

selected channels with the overload current within the different specified ranges (for both positive and

negative injection current).

Refer to scheme reported in Figure 43.

25.7.1

Conversion timing control

When a conversion is started, first the capacitances of the converter are loaded via the

respective analog input pin to the current analog input voltage. The time to load the

capacitances is referred to as sample time. Next the sampled voltage is converted to a

digital value several successive steps, which correspond to the 10-bit resolution of the ADC.

During these steps the internal capacitances are repeatedly charged and discharged via the

VAREF pin.

The current that has to be drawn from the sources for sampling and changing charges

depends on the time that each respective step takes, because the capacitors must reach

their final voltage level within the given time, at least with a certain approximation. The

maximum current, however, that a source can deliver, depends on its internal resistance.

The time that the two different actions during conversion take (sampling, and converting)

can be programmed within a certain range in the ST10F272Z2 relative to the CPU clock.

The absolute time that is consumed by the different conversion steps therefore is

independent from the general speed of the controller. This allows adjusting the A/D

converter of the ST10F272Z2 to the properties of the system:

Fast conversion can be achieved by programming the respective times to their absolute

possible minimum. This is preferable for scanning high frequency signals. The internal

resistance of analog source and analog supply must be sufficiently low, however.

High internal resistance can be achieved by programming the respective times to a higher

value, or the possible maximum. This is preferable when using analog sources and supply

with a high internal resistance in order to keep the current as low as possible. The

conversion rate in this case may be considerably lower, however.

The conversion times are programmed via the upper four bits of register ADCON. Bit fields

ADCTC and ADSTC are used to define the basic conversion time and in particular the

partition between sample phase and comparison phases. The table below lists the possible

combinations. The timings refer to the unit TCL, where fCPU = 1/2TCL. A complete

conversion time includes the conversion itself, the sample time and the time required to

transfer the digital value to the result register.

Table 69.

A/D converter programming

ADCTC

ADSTC

Sample

Comparison

Extra

Total conversion

TCL * 120

TCL * 240

TCL * 28

TCL * 388

TCL * 140

TCL * 280

TCL * 16

TCL * 436

TCL * 200

TCL * 280

TCL * 52

TCL * 532

TCL * 400

TCL * 280

TCL * 44

TCL * 724

ST10F272Z2T3 датащи(PDF) 147 Page - STMicroelectronics

ST10F272Z2T3 датащи(HTML) 147 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL