PIC24FJ16GA datasheet(90/262 Pages) MICROCHIP

90 / 262 page

PIC24FJ64GA004 FAMILY

DS39881C-page 88

Preliminary

7.1

CPU Clocking Scheme

The system clock source can be provided by one of

four sources:

• Primary Oscillator (POSC) on the OSCI and

OSCO pins

• Secondary Oscillator (SOSC) on the SOSCI and

SOSCO pins

• Fast Internal RC (FRC) Oscillator

• Low-Power Internal RC (LPRC) Oscillator

The primary oscillator and FRC sources have the

option of using the internal 4x PLL. The frequency of

the FRC clock source can optionally be reduced by the

programmable clock divider. The selected clock source

generates the processor and peripheral clock sources.

The processor clock source is divided by two to pro-

duce the internal instruction cycle clock, FCY. In this

document, the instruction cycle clock is also denoted

by FOSC/2. The internal instruction cycle clock, FOSC/2,

can be provided on the OSCO I/O pin for some

operating modes of the primary oscillator.

7.2

Initial Configuration on POR

The oscillator source (and operating mode) that is

used at a device Power-on Reset event is selected

using Configuration bit settings. The oscillator Config-

uration bit settings are located in the Configuration

registers

the

program

memory

(refer

Section 23.1 “Configuration Bits” for further

details). The Primary Oscillator Configuration bits,

POSCMD1:POSCMD0 (Configuration Word 2<1:0>),

and the Initial Oscillator Select Configuration bits,

FNOSC2:FNOSC0

(Configuration Word 2<10:8>),

select the oscillator source that is used at a Power-on

Reset. The FRC primary oscillator with postscaler

(FRCDIV) is the default (unprogrammed) selection.

The secondary oscillator, or one of the internal

oscillators, may be chosen by programming these bit

locations.

The Configuration bits allow users to choose between

the various clock modes, shown in Table 7-1.

7.2.1

CLOCK SWITCHING MODE

CONFIGURATION BITS

The

FCKSM

Configuration

bits

(Configuration

Word 2<7:6>) are used to jointly configure device clock

switching and the Fail-Safe Clock Monitor (FSCM).

Clock switching is enabled only when FCKSM1 is

programmed (‘0’). The FSCM is enabled only when

FCKSM1:FCKSM0 are both programmed (‘00’).

TABLE 7-1:

CONFIGURATION BIT VALUES FOR CLOCK SELECTION

Oscillator Mode

Oscillator Source

POSCMD1:

POSCMD0

FNOSC2:

FNOSC0

Note

Fast RC Oscillator with Postscaler

(FRCDIV)

Internal

111

1, 2

(Reserved)

Internal

110

Low-Power RC Oscillator (LPRC)

Internal

101

Secondary (Timer1) Oscillator

(SOSC)

Secondary

100

Primary Oscillator (XT) with PLL

Module (XTPLL)

Primary

011

Primary Oscillator (EC) with PLL

Module (ECPLL)

Primary

011

Primary Oscillator (HS)

Primary

010

Primary Oscillator (XT)

Primary

010

Primary Oscillator (EC)

Primary

010

Fast RC Oscillator with PLL Module

(FRCPLL)

Internal

001

Fast RC Oscillator (FRC)

Internal

000

Note 1:

OSCO pin function is determined by the OSCIOFCN Configuration bit.

This is the default oscillator mode for an unprogrammed (erased) device.

PIC24FJ16GA датащи(PDF) 90 Page - Microchip Technology

PIC24FJ16GA датащи(HTML) 90 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL