32C datasheet(31/55 Pages) RENESAS

31 / 55 page

R8C/32C Group

5. Electrical Characteristics

R01DS0009EJ0100 Rev 1.00

Page 31 of 52

Aug. 24, 2010

Notes:

VCC = 2.7 to 5.5 V and Topr =

−20 to 85°C (N version) / −40 to 85°C (D version), unless otherwise specified.

Definition of programming/erasure endurance

The programming and erasure endurance is defined on a per-block basis.

If the programming and erasure endurance is n (n = 10,000), each block can be erased n times. For example, if 1,024 1-byte

writes are performed to different addresses in block A, a 1 Kbyte block, and then the block is erased, the

programming/erasure endurance still stands at one.

However, the same address must not be programmed more than once per erase operation (overwriting prohibited).

Endurance to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed).

In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential

addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example,

when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups

before erasing them all in one operation. In addition, averaging the erasure endurance between blocks A to D can further

reduce the actual erasure endurance. It is also advisable to retain data on the erasure endurance of each block and limit the

number of erase operations to a certain number.

If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase

command at least three times until the erase error does not occur.

Customers desiring program/erase failure rate information should contact their Renesas technical support representative.

−40°C for D version.

The data hold time includes time that the power supply is off or the clock is not supplied.

Figure 5.2

Time delay until Suspend

Table 5.6

Flash Memory (Data flash Block A to Block D) Electrical Characteristics

Symbol

Parameter

Conditions

Standard

Unit

Min.

Typ.

Max.

−

Program/erase endurance (2)

10,000 (3)

−−

times

−

Byte program time

(program/erase endurance

≤ 1,000 times)

−

160

1,500

µs

−

Byte program time

(program/erase endurance

> 1,000 times)

−

300

1,500

µs

−

Block erase time

(program/erase endurance

≤ 1,000 times)

−

0.2

−

Block erase time

(program/erase endurance

> 1,000 times)

−

0.3

td(SR-SUS)

Time delay from suspend request until

suspend

−−

5 + CPU clock

× 3 cycles

−

Interval from erase start/restart until

following suspend request

−−

µs

−

Time from suspend until erase restart

−−

30+CPU clock

× 1 cycle

µs

td(CMDRST-

READY)

Time from when command is forcibly

terminated until reading is enabled

−−

30+CPU clock

× 1 cycle

µs

−

Program, erase voltage

2.7

−

5.5

−

Read voltage

1.8

−

5.5

−

Program, erase temperature

−20 (7)

−

°C

−

Data hold time (8)

Ambient temperature = 55

°C20

−−

year

FST6 bit

Suspend request

(FMR21 bit)

Fixed time

td(SR-SUS)

Clock-dependent

time

Access restart

FST6, FST7: Bit in FST register

FMR21: Bit in FMR2 register

FST7 bit

32C датащи(PDF) 31 Page - Renesas Technology Corp

32C датащи(HTML) 31 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55

датащи скачать

ссылки URL