SC643EVB datasheet(17/26 Pages) SEMTECH

17 / 26 page

SC643

HOLDD

when the pulse train is completed. If the proper

hold time is not received, the interface will keep counting

pulses until the hold time is detected. If the total exceeds

63 pulses, the write will be ignored and the bus will reset

after the next valid hold time is detected. After the bus

has been held high for t

HOLDD

, the bus will expect the next

pulse set to be an address write. Note that this is the same

effect as the bus reset that occurs when t

HOLDA

exceeds its

maximum specification. For this reason, there is no

maximum limit on t

HOLDD

— the bus simply waits for the

next valid address to be transmitted.

Multiple Writes

It is important to note that this single-wire interface

requires the address to be paired with its corresponding

data. If it is desired to write multiple times to the same

address, the address must always be re-transmitted prior

to the corresponding data. If it is only transmitted one

time and followed by multiple data transmissions, every

other block of data will be treated like a new address. The

result will be invalid data writes to incorrect addresses.

Note that multiple writes only need to be separated by

the minimum t

HOLDD

for the slave to interpret them cor-

rectly. As long as t

HOLDA

between the address pulse set and

the data pulse set is less than its maximum specification

but greater than its minimum, multiple pairs of address

and data pulse counts can be made with no detrimental

effects.

Standby Mode

Once data transfer is completed, the SPIF line must be

returned to the high state for at least 10ms to return to the

standby mode. In this mode, the SPIF line remains idle

while monitoring for the next command. This mode

allows the device to minimize current consumption

between commands. Once the device has returned to

standby mode, the bus is automatically reset to accept the

address pulses as the next data block. This safeguard is

intended to reset the bus to a known state (waiting for the

beginning of a write sequence) if the delay exceeds the

reset threshold.

Introduction

SemPulse is a write-only single wire interface. It provides

access to up to 32 registers that control device functional-

ity. Two sets of pulse trains are transmitted to generate a

complete SemPulse command. The first pulse set is used

to set the desired address. After the bus is held high for

the address hold period, the next pulse set is used to write

the data value. After the data pulses are transmitted, the

bus is held high again for the data hold period to signify

the data write is complete. At this point the device latches

the data into the address that was selected by the first set

of pulses. See the SemPulse Timing Diagrams for descrip-

tions of all timing parameters.

Chip Enable/Disable

The device is enabled when the SemPulse interface pin

(SPIF) is pulled high for greater than t

. If the SPIF pin is

pulled low again for more than t

, the device will be

disabled.

Address Writes

The first set of pulses can range between 0 and 31 (or 1 to

32 rising edges) to set the desired address. After the

pulses are transmitted, the SPIF pin must be held high for

HOLDA

to signal to the slave device that the address write is

finished. If the pulse count is between 0 and 31 and the

line is held high for t

HOLDA

, the address is latched as the

destination for the data word. If the SPIF pin is not held

high for t

HOLDA

, the slave device will continue to count

pulses. If the total exceeds 31 pulses, the write will be

ignored and the bus will reset after the next valid hold

time is detected. Note that if t

HOLDA

exceeds its maximum

specification, the bus will reset. This means that the com-

munication is ignored and the bus resumes monitoring

the pin, expecting the next pulse set to be an address.

Data Writes

After the bus has been held high for the minimum address

hold period, the next set of pulses are used to write the

data value. The total number of pulses can range from 0

to 63 (or 1 to 64 rising edges) since there are a total of 6

the data write is only accepted if the bus is held high for

SemPulse

® Interface

SC643EVB датащи(PDF) 17 Page - Semtech Corporation

SC643EVB датащи(HTML) 17 Page - Semtech Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

датащи скачать

ссылки URL