поискавой системы для электроныых деталей
  Russian  ▼
ALLDATASHEETRU.COM

X  

TD350 датащи(PDF) 9 Page - STMicroelectronics

номер детали TD350
подробное описание детали  Advanced IGBT/MOSFET driver
PDF  17 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
производитель  STMICROELECTRONICS [STMicroelectronics]
домашняя страница  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

TD350 датащи(HTML) 9 Page - STMicroelectronics

Back Button TD350 Datasheet HTML 5Page - STMicroelectronics TD350 Datasheet HTML 6Page - STMicroelectronics TD350 Datasheet HTML 7Page - STMicroelectronics TD350 Datasheet HTML 8Page - STMicroelectronics TD350 Datasheet HTML 9Page - STMicroelectronics TD350 Datasheet HTML 10Page - STMicroelectronics TD350 Datasheet HTML 11Page - STMicroelectronics TD350 Datasheet HTML 12Page - STMicroelectronics TD350 Datasheet HTML 13Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 17 page
background image
TD350
Functional description
Doc ID 9525 Rev 6
9/17
5.6
Minimum ON time
In order to ensure the proper operation of the 2-level turn-off function, the input ON time
(Twin) must be greater than the Twinmin value:
Twinmin=Ta+2*Rdel*Coff
Rdel is the internal discharge resistor and Coff is the external timing capacitor.
Input signals smaller than Ta are ignored. Input signals larger than Twinmin are transmitted to
the output stage after the Ta delay with minimum width distortion (ΔTw=Twout-Twin).
For an input signal width Twin between Ta and Twinmin, the output width Twout is reduced
below Twin (pulse distortion) and the IGBT could be partially turned on. These input signals
should be avoided during normal operation.
5.7
Output
The output stage is able to sink 2.3 A and source 1.5 A typical at 25 °C (1.2 A/0.75 A
minimum over the full temperature range). Separated sink and source outputs allow
independent gate charge and discharge control without an extra external diode.
5.8
Fault status output
Fault output is used to signal a fault event (desaturation, UVLO) to a controller. The fault pin
is designed to drive an optocoupler.
5.9
Undervoltage protection
Undervoltage detection protects the application in the event of a low VH supply voltage
(during start-up or a fault situation). During undervoltage, the OUTH pin is open and the
OUTL pin is driven low (active pull-down for VH>2 V, passive pull-down for VH<2 V). Fault
output signals the undervoltage state and is reset only when undervoltage state disappears.
Figure 3.
Undervoltage protection
VH
OUT
2V
UVH
UVL
Vccmin
FAULT



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


датащи скачать

Go To PDF Page


ссылки URL



Вашему бизинису помогли Аллдатащит?  [ DONATE ] 

Что такое Аллдатащит   |   реклама   |   контакт   |   Конфиденциальность   |   Ссылка на техническое описание    |   обмен ссыками   |   поиск по производителю
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com