CAT5409 datasheet(3/16 Pages) ONSEMI

3 / 16 page

CAT5409

Doc. No. MD-2010 Rev. M

Characteristics subject to change without notice

ABSOLUTE MAXIMUM RATINGS(1)

Parameters

Ratings

Units

Temperature Under Bias

-55 to +125

ºC

Storage Temperature

-65 to +150

°C

Voltage on Any Pin with Respect to VSS

(1) (2)

-2.0 to +VCC + 2.0

VCC with Respect to Ground

-2.0 to +7.0

Package Power Dissipation Capability (TA = 25ºC)

1.0

Lead Soldering Temperature (10 s)

300

ºC

Wiper Current

±12

RECOMMENDED OPERATING CONDITIONS

Parameters

Ratings

Units

VCC

+2.5 to +6

Industrial Temperature

-40 to +85

°C

POTENTIOMETER CHARACTERISTICS

Over recommended operating conditions unless otherwise stated.

Symbol

Parameter

Test Conditions

Min

Typ

Max

Units

RPOT

Potentiometer Resistance (-00)

100

kΩ

RPOT

Potentiometer Resistance (-50)

kΩ

RPOT

Potentiometer Resistance (-10)

kΩ

RPOT

Potentiometer Resistance (-2.5)

2.5

kΩ

Potentiometer Resistance

Tolerance

±20

RPOT Matching

Power Rating

25°C, each pot

Wiper Current

±6

Wiper Resistance

IW = ±3 mA @ VCC = 3 V

300

Ω

Wiper Resistance

IW = ±3 mA @ VCC = 5 V

150

Ω

VTERM

Voltage on any RH or RL Pin

VSS = 0 V

GND

VCC

Resolution

1.6

Absolute Linearity

(5)

RW(n)(actual) - R(n)(expected)

(8)

±1

LSB

(7)

Relative Linearity

(6)

RW(n+1) - [RW(n) + LSB]

(8)

±0.2

LSB

(7)

TCRPOT

Temperature Coefficient of RPOT

(4)

±300

ppm/ºC

TCRATIO

Ratiometric Temp. Coefficient

(4)

ppm/ºC

CH/CL/CW Potentiometer Capacitances

(4)

10/10/25

Frequency Response

RPOT = 50 kΩ

(4)

0.4

MHz

Notes:

(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings

only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this

specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.

(2) The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC

voltage on output pins is VCC +0.5 V, which may overshoot to VCC +2.0 V for periods of less than 20 ns.

(3) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1 V to VCC +1 V.

(4) This parameter is tested initially and after a design or process change that affects the parameter.

(5) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer.

(6) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentio-

meter. It is a measure of the error in step size.

(7) LSB = RTOT / 63 or (RH - RL) / 63, single pot.

(8) n = 0, 1, 2, ..., 63

CAT5409 датащи(PDF) 3 Page - ON Semiconductor

CAT5409 датащи(HTML) 3 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

датащи скачать

ссылки URL