PIC12F1822-ISLASHMF datasheet(281/398 Pages) MICROCHIP

281 / 398 page

 2010 Microchip Technology Inc.

Preliminary

DS41413A-page 281

PIC12F/LF1822/16F/LF1823

25.1

EUSART Asynchronous Mode

The EUSART transmits and receives data using the

standard non-return-to-zero (NRZ) format. NRZ is

implemented with two levels: a VOH mark state which

represents a ‘1’ data bit, and a VOL space state which

represents a ‘0’ data bit. NRZ refers to the fact that

consecutively transmitted data bits of the same value

stay at the output level of that bit without returning to a

neutral level between each bit transmission. An NRZ

transmission port idles in the mark state. Each character

transmission consists of one Start bit followed by eight

or nine data bits and is always terminated by one or

more Stop bits. The Start bit is always a space and the

Stop bits are always marks. The most common data

format is 8 bits. Each transmitted bit persists for a period

of 1/(Baud Rate). An on-chip dedicated 8-bit/16-bit Baud

Rate Generator is used to derive standard baud rate

frequencies from the system oscillator. See Table 25-5

for examples of baud rate configurations.

The EUSART transmits and receives the LSb first. The

EUSART’s transmitter and receiver are functionally

independent, but share the same data format and baud

rate. Parity is not supported by the hardware, but can

be implemented in software and stored as the ninth

data bit.

25.1.1

EUSART ASYNCHRONOUS

TRANSMITTER

The EUSART transmitter block diagram is shown in

Figure 25-1. The heart of the transmitter is the serial

Transmit Shift Register (TSR), which is not directly

accessible by software. The TSR obtains its data from

the transmit buffer, which is the TXREG register.

25.1.1.1

Enabling the Transmitter

The EUSART transmitter is enabled for asynchronous

operations by configuring the following three control

bits:

•TXEN = 1

• SYNC = 0

• SPEN = 1

All other EUSART control bits are assumed to be in

their default state.

Setting the TXEN bit of the TXSTA register enables the

transmitter circuitry of the EUSART. Clearing the SYNC

bit of the TXSTA register configures the EUSART for

asynchronous operation. Setting the SPEN bit of the

RCSTA register enables the EUSART. The programmer

must set the corresponding TRIS bit to configure the

TX/CK I/O pin as an output.

25.1.1.2

Transmitting Data

A transmission is initiated by writing a character to the

TXREG register. If this is the first character, or the

previous character has been completely flushed from

the TSR, the data in the TXREG is immediately

transferred to the TSR register. If the TSR still contains

all or part of a previous character, the new character

data is held in the TXREG until the Stop bit of the

previous character has been transmitted. The pending

character in the TXREG is then transferred to the TSR

in one TCY immediately following the Stop bit

transmission. The transmission of the Start bit, data bits

and Stop bit sequence commences immediately

following the transfer of the data to the TSR from the

TXREG.

25.1.1.3

Transmit Interrupt Flag

The TXIF interrupt flag bit of the PIR1 register is set

whenever the EUSART transmitter is enabled and no

character is being held for transmission in the TXREG.

In other words, the TXIF bit is only clear when the TSR

is busy with a character and a new character has been

queued for transmission in the TXREG. The TXIF flag bit

is not cleared immediately upon writing TXREG. TXIF

becomes valid in the second instruction cycle following

the write execution. Polling TXIF immediately following

the TXREG write will return invalid results. The TXIF bit

is read-only, it cannot be set or cleared by software.

The TXIF interrupt can be enabled by setting the TXIE

interrupt enable bit of the PIE1 register. However, the

TXIF flag bit will be set whenever the TXREG is empty,

regardless of the state of TXIE enable bit.

To use interrupts when transmitting data, set the TXIE

bit only when there is more data to send. Clear the

TXIE interrupt enable bit upon writing the last character

of the transmission to the TXREG.

Note 1: The TXIF Transmitter Interrupt flag is set

when the TXEN enable bit is set.

PIC12F1822-I/MF датащи(PDF) 281 Page - Microchip Technology

PIC12F1822-I/MF датащи(HTML) 281 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL