AD7606BSTZ datasheet(13/36 Pages) AD

13 / 36 page

AD7606/AD7606-6/AD7606-4

Rev. 0 | Page 13 of 36

AD7606-4

TOP VIEW

(Not to Scale)

64 63 62

60 59 58

57 56 55 54 53 52 51 50 49

PIN 1

17 18

21 22 23

24 25 26

27 28 29 30 31 32

AGND

AVCC 1

FRSTDATA

OS 2

DB0

BUSY

CONVST B

CONVST A

RANGE

RESET

RD/SCLK

PAR/SER/BYTE SEL

OS 1

OS 0

STBY

DECOUPLING CAP PIN

DATA OUTPUT

POWER SUPPLY

ANALOG INPUT

GROUND PIN

DIGITAL OUTPUT

DIGITAL INPUT

REFERENCE INPUT/OUTPUT

DB15/BYTE SEL

REFIN/REFOUT

AGND

AVCC

REFGND

REFCAPA

AGND

REFCAPB

REFGND

REGCAP

AVCC

REF SELECT

Figure 10. AD7606-4 Pin Configuration

Table 6. Pin Function Descriptions

Pin No.

Type1

Mnemonic

Description

AD7606

AD7606-6

AD7606-4

1, 37, 38,

AVCC

Analog Supply Voltage, 4.75 V to 5.25 V. This supply voltage is applied to

the internal front end amplifiers and to the ADC core. These supply pins

should be decoupled to AGND.

2, 26, 35,

40, 41, 47

AGND

Analog Ground. These pins are the ground reference points for all analog

circuitry on the AD7606. All analog input signals and external reference

signals should be referred to these pins. All six of these AGND pins should

connect to the AGND plane of a system.

5, 4, 3

OS [2:0]

Oversampling Mode Pins. Logic inputs. These inputs are used to select the

oversampling ratio. OS 2 is the MSB control bit, and OS 0 is the LSB control

bit. See the Digital Filter section for more details about the oversampling

mode of operation and Table 9 for oversampling bit decoding.

PAR/SER/

BYTE SEL

PAR/SER/

BYTE SEL

PAR/SER/

BYTE SEL

Parallel/Serial/Byte Interface Selection Input. Logic input. If this pin is tied to

a logic low, the parallel interface is selected. If this pin is tied to a logic high,

the serial interface is selected. Parallel byte interface mode is selected when

this pin is logic high and DB15/BYTE SEL is logic high (see Table 8).

In serial mode, the RD/SCLK pin functions as the serial clock input. The

DB7/DOUTA pin and the DB8/DOUTB pin function as serial data outputs. When

the serial interface is selected, the DB[15:9] and DB[6:0] pins should be tied to

ground.

In byte mode, DB15, in conjunction with PAR/SER/BYTE SEL, is used to select

the parallel byte mode of operation (see

). DB14 is used as the HBEN

pin. DB[7:0] transfer the 16-bit conversion results in two

Table 8

RD operations,

with DB0 as the LSB of the data transfers.

STBY

Standby Mode Input. This pin is used to place the AD7606/AD7606-6/

AD7606-4 into one of two power-down modes: standby mode or shutdown

mode. The power-down mode entered depends on the state of the RANGE

pin, as shown in Table 7. When in standby mode, all circuitry, except the on-

chip reference, regulators, and regulator buffers, is powered down. When

in shutdown mode, all circuitry is powered down.

AD7606BSTZ датащи(PDF) 13 Page - Analog Devices

AD7606BSTZ датащи(HTML) 13 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

датащи скачать

ссылки URL