ATmega128 datasheet(232/386 Pages) ATMEL

232 / 386 page

232

2467S–AVR–07/09

ATmega128

Operation

The ADC converts an analog input voltage to a 10-bit digital value through successive approxi-

mation. The minimum value represents GND and the maximum value represents the voltage on

the AREF pin minus 1 LSB. Optionally, AVCC or an internal 2.56V reference voltage may be

connected to the AREF pin by writing to the REFSn bits in the ADMUX Register. The internal

voltage reference may thus be decoupled by an external capacitor at the AREF pin to improve

noise immunity.

The analog input channel and differential gain are selected by writing to the MUX bits in

ADMUX. Any of the ADC input pins, as well as GND and a fixed bandgap voltage reference, can

be selected as single ended inputs to the ADC. A selection of ADC input pins can be selected as

positive and negative inputs to the differential gain amplifier.

If differential channels are selected, the differential gain stage amplifies the voltage difference

between the selected input channel pair by the selected gain factor. This amplified value then

becomes the analog input to the ADC. If single ended channels are used, the gain amplifier is

bypassed altogether.

The ADC is enabled by setting the ADC Enable bit, ADEN in ADCSRA. Voltage reference and

input channel selections will not go into effect until ADEN is set. The ADC does not consume

power when ADEN is cleared, so it is recommended to switch off the ADC before entering power

saving sleep modes.

The ADC generates a 10-bit result which is presented in the ADC Data Registers, ADCH and

ADCL. By default, the result is presented right adjusted, but can optionally be presented left

adjusted by setting the ADLAR bit in ADMUX.

If the result is left adjusted and no more than 8-bit precision is required, it is sufficient to read

ADCH. Otherwise, ADCL must be read first, then ADCH, to ensure that the content of the data

registers belongs to the same conversion. Once ADCL is read, ADC access to data registers is

blocked. This means that if ADCL has been read, and a conversion completes before ADCH is

read, neither register is updated and the result from the conversion is lost. When ADCH is read,

ADC access to the ADCH and ADCL Registers is re-enabled.

The ADC has its own interrupt which can be triggered when a conversion completes. When ADC

access to the data registers is prohibited between reading of ADCH and ADCL, the interrupt will

trigger even if the result is lost.

Starting a

Conversion

A single conversion is started by writing a logical one to the ADC Start Conversion bit, ADSC.

This bit stays high as long as the conversion is in progress and will be cleared by hardware

when the conversion is completed. If a different data channel is selected while a conversion is in

progress, the ADC will finish the current conversion before performing the channel change.

In Free Running mode, the ADC is constantly sampling and updating the ADC Data Register.

Free Running mode is selected by writing the ADFR bit in ADCSRA to one. The first conversion

must be started by writing a logical one to the ADSC bit in ADCSRA. In this mode the ADC will

perform successive conversions independently of whether the ADC Interrupt Flag, ADIF is

cleared or not.

ATmega128 датащи(PDF) 232 Page - ATMEL Corporation

ATmega128 датащи(HTML) 232 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL