ATmega128 datasheet(127/386 Pages) ATMEL

127 / 386 page

127

2467S–AVR–07/09

ATmega128

The PWM frequency for the output can be calculated by the following equation:

The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).

The extreme values for the OCRnx Register represents special cases when generating a PWM

waveform output in the fast PWM mode. If the OCRnx is set equal to BOTTOM (0x0000) the out-

put will be a narrow spike for each TOP+1 timer clock cycle. Setting the OCRnx equal to TOP

will result in a constant high or low output (depending on the polarity of the output set by the

COMnx1:0 bits.)

A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by set-

ting OCnA to toggle its logical level on each compare match (COMnA1:0 = 1). This applies only

if OCRnA is used to define the TOP value (WGMn3:0 = 15). The waveform generated will have

a maximum frequency of f

OCnA = fclk_I/O/2 when OCRnA is set to zero (0x0000). This feature is

similar to the OCnA toggle in CTC mode, except the double buffer feature of the output compare

unit is enabled in the fast PWM mode.

Phase Correct PWM

Mode

The phase correct Pulse Width Modulation or phase correct PWM mode (WGMn3:0 = 1, 2, 3,

10, or 11) provides a high resolution phase correct PWM waveform generation option. The

phase correct PWM mode is, like the phase and frequency correct PWM mode, based on a dual-

slope operation. The counter counts repeatedly from BOTTOM (0x0000) to TOP and then from

TOP to BOTTOM. In non-inverting compare output mode, the output compare (OCnx) is cleared

on the compare match between TCNTn and OCRnx while counting up, and set on the compare

match while downcounting. In inverting Output Compare mode, the operation is inverted. The

dual-slope operation has lower maximum operation frequency than single slope operation. How-

ever, due to the symmetric feature of the dual-slope PWM modes, these modes are preferred for

motor control applications.

The PWM resolution for the phase correct PWM mode can be fixed to 8-, 9-, or 10-bit, or defined

by either ICRn or OCRnA. The minimum resolution allowed is 2 bit (ICRn or OCRnA set to

0x0003), and the maximum resolution is 16 bit (ICRn or OCRnA set to MAX). The PWM resolu-

tion in bits can be calculated by using the following equation:

In phase correct PWM mode the counter is incremented until the counter value matches either

one of the fixed values 0x00FF, 0x01FF, or 0x03FF (WGMn3:0 = 1, 2, or 3), the value in ICRn

(WGMn3:0 = 10), or the value in OCRnA (WGMn3:0 = 11). The counter has then reached the

TOP and changes the count direction. The TCNTn value will be equal to TOP for one timer clock

cycle. The timing diagram for the phase correct PWM mode is shown on Figure 53. The figure

shows phase correct PWM mode when OCRnA or ICRn is used to define TOP. The TCNTn

value is in the timing diagram shown as a histogram for illustrating the dual-slope operation. The

diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on

the TCNTn slopes represent compare matches between OCRnx and TCNTn. The OCnx inter-

rupt flag will be set when a compare match occurs.

fOCnxPWM

clk_I/O

TOP

()

⋅

-----------------------------------

RPCPWM

TOP 1

()

log

()

log

-----------------------------------

ATmega128 датащи(PDF) 127 Page - ATMEL Corporation

ATmega128 датащи(HTML) 127 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL