ATmega162 datasheet(233/324 Pages) ATMEL

233 / 324 page

233

2513K–AVR–07/09

ATmega162/V

Notes:

1. The SPIEN Fuse is not accessible in SPI Serial Programming mode.

2. The default value of BOOTSZ1:0 results in maximum Boot Size. See Table 93 on page 228 for

details.

3. Never ship a product with the OCDEN Fuse programmed regardless of the setting of Lock bits

and the JTAGEN Fuse. A programmed OCDEN Fuse enables some parts of the clock system

to be running in all sleep modes. This may increase the power consumption.

4. If the JTAG interface is left unconnected, the JTAGEN fuse should if possible be disabled. This

to avoid static current at the TDO pin in the JTAG interface.

Notes:

1. The default value of SUT1:0 results in maximum start-up time for the default clock source. See

Table 12 on page 39 for details.

2. The default setting of CKSEL3:0 results in Internal RC Oscillator @ 8 MHz. See Table 5 on

page 36 for details.

3. The CKOUT Fuse allow the system clock to be output on PortB 0. See “Clock output buffer” on

page 40 for details.

4. See “System Clock Prescaler” on page 41 for details.

The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are locked if

Lock bit1 (LB1) is programmed. Program the Fuse bits before programming the Lock bits.

Table 99. Fuse High Byte

Fuse Low Byte

Bit no

Description

Default Value

OCDEN(3)

Enable OCD

1 (unprogrammed, OCD

disabled)

JTAGEN(4)

Enable JTAG

0 (programmed, JTAG

enabled)

SPIEN(1)

Enable Serial Program and Data

Downloading

0 (programmed, SPI prog.

enabled)

WDTON

Watchdog Timer always on

1 (unprogrammed)

EESAVE

EEPROM memory is preserved

through the Chip Erase

1 (unprogrammed,

EEPROM not preserved)

BOOTSZ1

Select Boot Size (see Table 93 for

details)

0 (programmed)(2)

BOOTSZ0

Select Boot Size (see Table 93 for

details)

0 (programmed)(2)

BOOTRST

Select Reset Vector

1 (unprogrammed)

Table 100. Fuse Low Byte

Fuse Low Byte

Bit no

Description

Default value

CKDIV8(4)

Divide clock by 8

0 (programmed)

CKOUT(3)

Clock Output

1 (unprogrammed)

SUT1

Select start-up time

1 (unprogrammed)(1)

SUT0

Select start-up time

0 (programmed)(1)

CKSEL3

Select Clock source

0 (programmed)(2)

CKSEL2

Select Clock source

0 (programmed)(2)

CKSEL1

Select Clock source

1 (unprogrammed)(2)

CKSEL0

Select Clock source

0 (programmed)(2)

ATmega162 датащи(PDF) 233 Page - ATMEL Corporation

ATmega162 датащи(HTML) 233 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL