ATmega162 datasheet(146/324 Pages) ATMEL

146 / 324 page

146

2513K–AVR–07/09

ATmega162/V

The extreme values for the OCR2 Register represent special cases when generating a PWM

waveform output in the fast PWM mode. If the OCR2 is set equal to BOTTOM, the output will be

a narrow spike for each MAX+1 timer clock cycle. Setting the OCR2 equal to MAX will result in a

constantly high or low output (depending on the polarity of the output set by the COM21:0 bits.)

A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by set-

ting OC2 to toggle its logical level on each Compare Match (COM21:0 = 1). The waveform

generated will have a maximum frequency of f

oc2 = fclk_I/O/2 when OCR2 is set to zero. This fea-

ture is similar to the OC2 toggle in CTC mode, except the double buffer feature of the Output

Compare unit is enabled in the fast PWM mode.

Phase Correct PWM

Mode

The phase correct PWM mode (WGM21:0 = 3) provides a high resolution phase correct PWM

waveform generation option. The phase correct PWM mode is based on a dual-slope operation.

The counter counts repeatedly from BOTTOM to MAX and then from MAX to BOTTOM. In non-

inverting Compare Output mode, the Output Compare (OC2) is cleared on the Compare Match

between TCNT2 and OCR2 while up-counting, and set on the Compare Match while down-

counting. In inverting output compare mode, the operation is inverted. The dual-slope operation

has lower maximum operation frequency than single slope operation. However, due to the sym-

metric feature of the dual-slope PWM modes, these modes are preferred for motor control

applications.

The PWM resolution for the phase correct PWM mode is fixed to eight bits. In phase correct

PWM mode the counter is incremented until the counter value matches MAX. When the counter

reaches MAX, it changes the count direction. The TCNT2 value will be equal to MAX for one

timer clock cycle. The timing diagram for the phase correct PWM mode is shown on Figure 65.

The TCNT2 value is in the timing diagram shown as a histogram for illustrating the dual-slope

operation. The diagram includes non-inverted and inverted PWM outputs. The small horizontal

line marks on the TCNT2 slopes represent compare matches between OCR2 and TCNT2.

Figure 65. Phase Correct PWM Mode, Timing Diagram

The Timer/Counter Overflow Flag (TOV2) is set each time the counter reaches BOTTOM. The

Interrupt Flag can be used to generate an interrupt each time the counter reaches the BOTTOM

value.

In phase correct PWM mode, the compare unit allows generation of PWM waveforms on the

OC2 pin. Setting the COM21:0 bits to two will produce a non-inverted PWM. An inverted PWM

output can be generated by setting the COM21:0 to three (See Table 63 on page 150). The

TOVn Interrupt Flag Set

OCn Interrupt Flag Set

TCNTn

Period

OCn

(COMn1:0 = 2)

(COMn1:0 = 3)

OCRn Update

ATmega162 датащи(PDF) 146 Page - ATMEL Corporation

ATmega162 датащи(HTML) 146 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL