ATmega16 datasheet(251/357 Pages) ATMEL

251 / 357 page

251

2466S–AVR–05/09

ATmega16(L)

• Bit 2 – PGWRT: Page Write

If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock

cycles executes Page Write, with the data stored in the temporary buffer. The page address is

taken from the high part of the Z-pointer. The data in R1 and R0 are ignored. The PGWRT bit

will auto-clear upon completion of a page write, or if no SPM instruction is executed within four

clock cycles. The CPU is halted during the entire page write operation if the NRWW section is

addressed.

• Bit 1 – PGERS: Page Erase

If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock

cycles executes Page Erase. The page address is taken from the high part of the Z-pointer. The

data in R1 and R0 are ignored. The PGERS bit will auto-clear upon completion of a page erase,

or if no SPM instruction is executed within four clock cycles. The CPU is halted during the entire

page write operation if the NRWW section is addressed.

• Bit 0 – SPMEN: Store Program Memory Enable

This bit enables the SPM instruction for the next four clock cycles. If written to one together with

either RWWSRE, BLBSET, PGWRT’ or PGERS, the following SPM instruction will have a spe-

cial meaning, see description above. If only SPMEN is written, the following SPM instruction will

store the value in R1:R0 in the temporary page buffer addressed by the Z-pointer. The LSB of

the Z-pointer is ignored. The SPMEN bit will auto-clear upon completion of an SPM instruction,

or if no SPM instruction is executed within four clock cycles. During page erase and page write,

the SPMEN bit remains high until the operation is completed.

Writing any other combination than “10001”, “01001”, “00101”, “00011” or “00001” in the lower

five bits will have no effect.

Addressing the

Flash during Self-

Programming

The Z-pointer is used to address the SPM commands.

Since the Flash is organized in pages (see Table 107 on page 262), the Program Counter can

be treated as having two different sections. One section, consisting of the least significant bits, is

addressing the words within a page, while the most significant bits are addressing the pages.

This is shown in Figure 126. Note that the Page Erase and Page Write operations are addressed

independently. Therefore it is of major importance that the Boot Loader software addresses the

same page in both the Page Erase and Page Write operation. Once a programming operation is

initiated, the address is latched and the Z-pointer can be used for other operations.

The only SPM operation that does not use the Z-pointer is Setting the Boot Loader Lock bits.

The content of the Z-pointer is ignored and will have no effect on the operation. The LPM

instruction does also use the Z pointer to store the address. Since this instruction addresses the

Flash byte by byte, also the LSB (bit Z0) of the Z-pointer is used.

Bit

151413

1211

ZH (R31)

Z15

Z14

Z13

Z12

Z11

Z10

ZL (R30)

Z7Z6

Z5Z4Z3

Z2Z1Z0

765

432

ATmega16 датащи(PDF) 251 Page - ATMEL Corporation

ATmega16 датащи(HTML) 251 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL