ATmega16 datasheet(250/357 Pages) ATMEL

250 / 357 page

250

2466S–AVR–05/09

ATmega16(L)

Note:

1. “1” means unprogrammed, “0” means programmed

Store Program

Memory Control

The Store Program Memory Control Register contains the control bits needed to control the Boot

Loader operations.

• Bit 7 – SPMIE: SPM Interrupt Enable

When the SPMIE bit is written to one, and the I-bit in the Status Register is set (one), the SPM

ready interrupt will be enabled. The SPM ready Interrupt will be executed as long as the SPMEN

bit in the SPMCR Register is cleared.

• Bit 6 – RWWSB: Read-While-Write Section Busy

When a self-programming (Page Erase or Page Write) operation to the RWW section is initiated,

the RWWSB will be set (one) by hardware. When the RWWSB bit is set, the RWW section can-

not be accessed. The RWWSB bit will be cleared if the RWWSRE bit is written to one after a

Self-Programming operation is completed. Alternatively the RWWSB bit will automatically be

cleared if a page load operation is initiated.

• Bit 5 – Res: Reserved Bit

This bit is a reserved bit in the ATmega16 and always read as zero.

• Bit 4 – RWWSRE: Read-While-Write Section Read Enable

When programming (Page Erase or Page Write) to the RWW section, the RWW section is

blocked for reading (the RWWSB will be set by hardware). To re-enable the RWW section, the

user software must wait until the programming is completed (SPMEN will be cleared). Then, if

the RWWSRE bit is written to one at the same time as SPMEN, the next SPM instruction within

four clock cycles re-enables the RWW section. The RWW section cannot be re-enabled while

the Flash is busy with a page erase or a page write (SPMEN is set). If the RWWSRE bit is writ-

ten while the Flash is being loaded, the Flash load operation will abort and the data loaded will

be lost.

• Bit 3 – BLBSET: Boot Lock Bit Set

If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock

cycles sets Boot Lock bits, according to the data in R0. The data in R1 and the address in the Z-

pointer are ignored. The BLBSET bit will automatically be cleared upon completion of the Lock

bit set, or if no SPM instruction is executed within four clock cycles.

An LPM instruction within three cycles after BLBSET and SPMEN are set in the SPMCR Regis-

ter, will read either the Lock bits or the Fuse bits (depending on Z0 in the Z-pointer) into the

destination register. See “Reading the Fuse and Lock Bits from Software” on page 254 for

details.

Table 98. Boot Reset Fuse(1)

BOOTRST

Reset Address

Reset Vector = Application reset (address $0000)

Reset Vector = Boot Loader reset (see Table 100 on page 257)

Bit

210

SPMIE

RWWSB

–

RWWSRE

BLBSET

PGWRT

PGERS

SPMEN

SPMCR

Read/Write

R/W

Initial value

ATmega16 датащи(PDF) 250 Page - ATMEL Corporation

ATmega16 датащи(HTML) 250 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL