ATmega16 datasheet(122/357 Pages) ATMEL

122 / 357 page

122

2466S–AVR–05/09

ATmega16(L)

Modes of

Operation

The mode of operation, i.e., the behavior of the Timer/Counter and the output compare pins, is

defined by the combination of the Waveform Generation mode (WGM21:0) and Compare Output

mode (COM21:0) bits. The Compare Output mode bits do not affect the counting sequence,

while the Waveform Generation mode bits do. The COM21:0 bits control whether the PWM out-

put generated should be inverted or not (inverted or non-inverted PWM). For non-PWM modes

the COM21:0 bits control whether the output should be set, cleared, or toggled at a compare

match (See “Compare Match Output Unit” on page 121.).

For detailed timing information refer to “Timer/Counter Timing Diagrams” on page 126.

Normal Mode

The simplest mode of operation is the Normal mode (WGM21:0 = 0). In this mode the counting

direction is always up (incrementing), and no counter clear is performed. The counter simply

overruns when it passes its maximum 8-bit value (TOP = 0xFF) and then restarts from the bot-

tom (0x00). In normal operation the Timer/Counter Overflow Flag (TOV2) will be set in the same

timer clock cycle as the TCNT2 becomes zero. The TOV2 Flag in this case behaves like a ninth

bit, except that it is only set, not cleared. However, combined with the timer overflow interrupt

that automatically clears the TOV2 Flag, the timer resolution can be increased by software. There

are no special cases to consider in the normal mode, a new counter value can be written

anytime.

The Output Compare unit can be used to generate interrupts at some given time. Using the out-

put compare to generate waveforms in normal mode is not recommended, since this will occupy

too much of the CPU time.

Clear Timer on

Compare Match (CTC)

Mode

In Clear Timer on Compare or CTC mode (WGM21:0 = 2), the OCR2 Register is used to manip-

ulate the counter resolution. In CTC mode the counter is cleared to zero when the counter value

(TCNT2) matches the OCR2. The OCR2 defines the top value for the counter, hence also its

resolution. This mode allows greater control of the compare match output frequency. It also sim-

plifies the operation of counting external events.

The timing diagram for the CTC mode is shown in Figure 57. The counter value (TCNT2)

increases until a compare match occurs between TCNT2 and OCR2, and then counter (TCNT2)

is cleared.

Figure 57. CTC Mode, Timing Diagram

An interrupt can be generated each time the counter value reaches the TOP value by using the

OCF2 Flag. If the interrupt is enabled, the interrupt handler routine can be used for updating the

TOP value. However, changing the TOP to a value close to BOTTOM when the counter is run-

ning with none or a low prescaler value must be done with care since the CTC mode does not

have the double buffering feature. If the new value written to OCR2 is lower than the current

TCNTn

OCn

(Toggle)

OCn Interrupt Flag Set

Period

(COMn1:0 = 1)

ATmega16 датащи(PDF) 122 Page - ATMEL Corporation

ATmega16 датащи(HTML) 122 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL