• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400

• India Tel: +91.80.4155721

• China Tel: +86.21.2407.1588

Visit www.macomtech.com for additional data sheets and product information.

M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make

changes to the product(s) or information contained herein without notice.

3

GaAs SPDT Reflective Switch with TTL/CMOS Control Input,

DC-3.0 GHz

Rev. V6

SW-110-PIN

ADVANCED:

Data Sheets contain information regarding a product M/A-COM Technology Solutions

is considering for development. Performance is based on target specifications, simulated results,

and/or prototype measurements. Commitment to develop is not guaranteed.

PRELIMINARY:

Data Sheets contain information regarding a product M/A-COM Technology

Solutions has under development. Performance is based on engineering tests. Specifications are

typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.

Commitment to produce in volume is not guaranteed.

Absolute Maximum Ratings

4,5

Parameter

Absolute Maximum

Max Input Power

0.05 GHz

0.5 - 3.0 GHz

-5V Control

-8V Control

+35

+36

+39

2.0W

Operating Temperature

-55°C to +125°C

Storage Temperature

-65°C to +150°C

Junction Temperature

+175°C

Thermal Resistance

θjc

+50°C/W

4.

Exceeding any one or combination of these limits may cause

permanent damage to this device.

5.

M/A-COM does not recommend sustained operation near

these survivability limits.

6.

Tcase = 25°C, where Tcase is the temperature at the bottom

of the case.

7.

Special consideration must be given to the mounting of the

switch to minimize the thermal resistance. The bottom of the

case should be thermally attached to the mounting surface

to maintain the junction temperature under the absolute

maximum rating.

8.

Standard CMOS TTL interface, latch-up will occur if logic

signal is applied prior to power supply.

Handling Procedures

Please observe the following precautions to avoid

damage:

Static Sensitivity

Gallium Arsenide Integrated Circuits are sensitive

to electrostatic discharge (ESD) and can be

damaged by static electricity. Proper ESD control

techniques should be used when handling these

devices.

Truth Table (Switch)

Condition of Switch

RF Common to each RF Port

C1

RF1

RF2

0

On

Off

1

Off

On

Control Inputs

Bias

Voltage

Input

Power for

Each

Tone

(dBm)

3rd

Order

Intermod

Products

(dBc)

IP3

(dBm)

Second

Harmonic

(dBc)

0, -5V

0, -6V

0, -7V

0, -8V

+27

+27

+27

+27

-34

-49

-64

-65

+44

+51

+59

+59

-61

-61

-63

-63

0, -5V

0, -6V

0, -7V

0, -8V

+28

+28

+28

+28

-30

-41

-52

-60

+43

+48

+54

+58

-58

-58

-57

-57

0, -5V

0, -6V

0, -7V

0, -8V

+29

+29

+29

+29

-28

-34

-44

-52

+43

+46

+51

+55

-54

-54

-54

-54

0, -5V

0, -6V

0, -7V

0, -8V

+30

+30

+30

+30

-26

-32

-38

-44

+43

+46

+49

+52

-52

-51

-51

-51

0 = TTL Low; 1 = TTL High