SRT512 datasheet(25/46 Pages) STMICROELECTRONICS

25 / 46 page

SRT512

Anticollision

Doc ID 13277 Rev 4

25/46

7.1

Description of an anticollision sequence

The anticollision sequence is initiated by the Initiate() command which triggers all the

SRT512 devices that are present in the reader field range, and that are in Inventory state.

Only SRT512 devices in Inventory state will respond to the Pcall16() and Slot_marker(SN)

anticollision commands.

A new SRT512 introduced in the field range during the anticollision sequence will not be

taken into account as it will not respond to the Pcall16() or Slot_marker(SN) command

(Ready state). To be considered during the anticollision sequence, it must have received the

Initiate() command and entered the Inventory state.

Table 3 shows the elements of a standard anticollision sequence. (See Figure 21 for an

example.)

After each Slot_marker() command, there may be several, one or no answers from the

SRT512 devices. The reader must handle all the cases and store all the Chip_IDs, correctly

decoded. At the end of the anticollision sequence, after Slot_marker(15), the reader can

start working with one SRT512 by issuing a Select() command containing the desired

Chip_ID. If a collision is detected during the anticollision sequence, the reader has to

generate a new sequence in order to identify all unidentified SRT512 devices in the field.

The anticollision sequence can stop when all SRT512 devices have been identified.

Table 3.

Standard anticollision sequence

Step 1

Init:

Send Initiate().

– If no answer is detected, go to step1.

– If only 1 answer is detected, select and access the SRT512. After accessing the SRT512,

deselect the tag and go to step1.

– If a collision (many answers) is detected, go to step2.

Step 2

Slot 0

Send Pcall16().

– If no answer or collision is detected, go to step3.

– If 1 answer is detected, store the Chip_ID, Send Select() and go to step3.

Step 3

Slot 1

Send Slot_marker(1).

– If no answer or collision is detected, go to step4.

– If 1 answer is detected, store the Chip_ID, Send Select() and go to step4.

Step 4

Slot 2

Send Slot_marker(2).

– If no answer or collision is detected, go to step5.

– If 1 answer is detected, store the Chip_ID, Send Select() and go to step5.

Step N

Slop N

Send Slot_marker(3 up to 14)...

– If no answer or collision is detected, go to stepN+1.

– If 1 answer is detected, store the Chip_ID, Send Select() and go to stepN+1.

Step 17 Slot 15

Send Slot_marker(15).

– If no answer or collision is detected, go to step18.

– If 1 answer is detected, store the Chip_ID, Send Select() and go to step18.

Step 18

All the slots have been generated and the Chip_ID values should be stored into the

reader memory. Issue the Select(Chip_ID) command and access each identified

SRT512 one by one. After accessing each SRT512, switch them into Deselected or

Deactivated state, depending on the application needs.

– If collisions were detected between Step2 and Step17, go to Step2.

– If no collision was detected between Step2 and Step17, go to Step1.

SRT512 датащи(PDF) 25 Page - STMicroelectronics

SRT512 датащи(HTML) 25 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

датащи скачать

ссылки URL