| поискавой системы для электроныых деталей |
|
TMS320C28343ZHHT датащи(PDF) 55 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TMS320C28343ZHHT датащи(HTML) 55 Page - Texas Instruments |
|
55 / 153 page ![]() 3.6.1.3 Loss of Input Clock 3.6.2 Watchdog Block /512 OSCCLK WDCR(WDPS[2:0]) WDCLK WDCNTR(7:0) WDKEY(7:0) GoodKey 1 0 1 WDCR(WDCHK[2:0]) Bad WDCHK Key WDCR(WDDIS) ClearCounter SCSR(WDENINT) Watchdog Prescaler Generate OutputPulse (512OSCCLKs) 8-Bit Watchdog Counter CLR WDRST WDINT Watchdog 55+AA KeyDetector XRS Core-reset WDRST(A) Internal Pullup TMS320C28346, TMS320C28345, TMS320C28344 TMS320C28343, TMS320C28342, TMS320C28341 Delfino Microcontrollers www.ti.com SPRS516 – MARCH 2009 Table 3-14. Possible PLL Configuration Modes CLKIN AND PLL MODE REMARKS PLLSTS[DIVSEL](1) SYSCLKOUT Invoked by the user setting the PLLOFF bit in the PLLSTS register. The PLL block 0 OSCCLK/8 is disabled in this mode. This can be useful to reduce system noise and for low 1 OSCCLK/4 PLL Off power operation. The PLLCR register must first be set to 0x0000 (PLL Bypass) 2 OSCCLK/2 before entering this mode. The CPU clock (CLKIN) is derived directly from the 3 OSCCLK/1 input clock on either X1/X2, X1 or XCLKIN. PLL Bypass is the default PLL configuration upon power-up or after an external 0 OSCCLK/8 reset (XRS). This mode is selected when the PLLCR register is set to 0x0000 or 1 OSCCLK/4 PLL Bypass while the PLL locks to a new frequency after the PLLCR register has been 2 OSCCLK/2 modified. In this mode, the PLL itself is bypassed but the PLL is not turned off. 3 OSCCLK/1 0 OSCCLK*n/8 Achieved by writing a non-zero value n into the PLLCR register. Upon writing to the 1 OSCCLK*n/4 PLL Enable PLLCR the device will switch to PLL Bypass mode until the PLL locks. 2 OSCCLK*n/2 3 –(2) (1) PLLSTS[DIVSEL] must be 0 before writing to the PLLCR and must be set to 2 or 3 only after PLLSTS[PLLLOCKS] = 1. See the TMS320x2834x Delfino System Control and Interrupts Reference Guide (literature number SPRUFN1) for more information. (2) PLLSTS[DIVSEL] should not be set to /1 mode while the PLL is enabled and not bypassed. Applications in which the correct CPU operating frequency is absolutely critical should implement a mechanism by which the MCU will be held in reset, should the input clocks ever fail. For example, an R-C circuit may be used to trigger the XRS pin of the MCU, should the capacitor ever get fully charged. An I/O pin may be used to discharge the capacitor on a periodic basis to prevent it from getting fully charged. The watchdog block on the C2834x device is similar to the one used on the 240x and 281x devices. The watchdog module generates an output pulse, 512 oscillator clocks wide (OSCCLK), whenever the 8-bit watchdog up counter has reached its maximum value. To prevent this, the user disables the counter or the software must periodically write a 0x55 + 0xAA sequence into the watchdog key register which will reset the watchdog counter. Figure 3-13 shows the various functional blocks within the watchdog module. A. The WDRST signal is driven low for 512 OSCCLK cycles. Figure 3-13. Watchdog Module The WDINT signal enables the watchdog to be used as a wakeup from IDLE/STANDBY mode. Submit Documentation Feedback Functional Overview 55 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |