Notes:

Model

Number

Input

Output

Load

Regulation

(%, Max)

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load

No-Load

G201E

5

4.5 - 5.5

494

30

5.0

400.0

40.0

15

81

1,000

G202E

5

4.5 - 5.5

488

30

9.0

222.0

23.0

15

82

1,000

G203E

5

4.5 - 5.5

476

30

12.0

167.0

17.0

15

84

1,000

G204E

5

4.5 - 5.5

476

30

15.0

133.0

14.0

15

84

1,000

G205E

5

4.5 - 5.5

488

30

±5.0

±200.0

±20.0

15

82

1,000

G206E

5

4.5 - 5.5

482

30

±9.0

±111.0

±12.0

15

83

1,000

G207E

5

4.5 - 5.5

470

30

±12.0

±83.0

±9.0

15

85

1,000

G208E

5

4.5 - 5.5

470

30

±15.0

±67.0

±7.0

15

85

1,000

G211E

12

10.8 - 13.2

203

15

5.0

400.0

40.0

15

82

500

G212E

12

10.8 - 13.2

201

15

9.0

222.0

23.0

15

83

500

G213E

12

10.8 - 13.2

196

15

12.0

167.0

17.0

15

85

500

G214E

12

10.8 - 13.2

196

15

15.0

133.0

14.0

15

85

500

G215E

12

10.8 - 13.2

201

15

±5.0

±200.0

±20.0

15

83

500

G216E

12

10.8 - 13.2

198

15

±9.0

±111.0

±12.0

15

84

500

G217E

12

10.8 - 13.2

194

15

±12.0

±83.0

±9.0

15

86

500

G218E

12

10.8 - 13.2

194

15

±15.0

±67.0

±7.0

15

86

500

G221E

24

21.6 - 26.4

100

8

5.0

400.0

40.0

15

83

250

G222E

24

21.6 - 26.4

99

8

9.0

222.0

23.0

15

84

250

G223E

24

21.6 - 26.4

97

8

12.0

167.0

17.0

15

86

250

G224E

24

21.6 - 26.4

97

8

15.0

133.0

14.0

15

86

250

G225E

24

21.6 - 26.4

99

8

±5.0

±200.0

±20.0

15

84

250

G226E

24

21.6 - 26.4

98

8

±9.0

±111.0

±12.0

15

85

250

G227E

24

21.6 - 26.4

96

8

±12.0

±83.0

±9.0

15

87

250

G228E

24

21.6 - 26.4

96

8

±15.0

±67.0

±7.0

15

87

250

Pin

Single

Dual

Pin

Single

Dual

1

-Vin

-Vin

9

+Vout

+Vout

7

NC

NC

11

No Pin

-Vout

8

-Vout

Common

14

+Vin

+Vin

Derating Curve

Notes:

1. Output load regulation is specified for a load change of 10% to

100%.

2. These units should not be operated with a load under 10% of

full load. Operation at no-load may cause damage to the unit.

3. These converters will operate without external components.

However, when measuring output ripple, it is recommended

that an external ceramic capacitor be placed from the +Vout

pin to the -Vout pin for single output units and from each out-

put to common for dual output units. An input capacitor will

enhance stability over temperature and input line variations.

Recommended capacitor values are given in the table below.

For applications requiring very low output noise levels, a simple

LC filter should be effective.

4. Dual output units may be connected to provide a 10V, 18V, 24V

or 30 VDC output. To do this, connect the load across the posi-

tive (+Vout) and negative (-Vout) outputs and float the output

common

5. It is recommended that a fuse be used on the input of a power

supply for protection. See the Model Selection table above for

the correct rating.

Vin

Input

Capacitor

Vout

Output Capacitor

Single

Dual

5 VDC

4.7

µF

5 VDC

10.0

µF

4.7

µF

12 VDC

2.2

µF

9 VDC

4.7

µF

2.2

µF

24 VDC

1.0

µF

12 VDC

2.2

µF

1.0

µF

15 VDC

1.0

µF

0.47

µF

MicroPower Direct

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

Model Selection Guide

Mechanical Dimensions

Pin Connections