RH1016M datasheet(3/6 Pages) LINER

3 / 6 page

RH1016M

rh1016fa

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: Input offset voltage is deﬁned as the average of the two voltages

measured by forcing ﬁrst one output, then the other to 1.4V. Input offset

current is deﬁned in the same way.

Note 3: Input bias current (IB) is deﬁned as the average of the two input

currents.

Note 4: tPD and ΔtPD cannot be measured in automatic handling

equipment with low values of overdrive. The RH1016 is sample tested with

a 1V step and 500mV overdrive. Correlation tests have shown that tPD and

TABLE 1A: ELECTRICAL CHARACTERISTICS

(Postirradiation) TA = 25°C, V+ = 5V, V– = –5V, VOUT(Q) = 1.4V, VLATCH = 0V, unless otherwise noted.

SYMBOL PARAMETER

CONDITIONS

NOTES MIN

MAX

MIN

MAX

MIN

MAX

MIN

MAX

MIN

MAX

UNITS

VOS

Input Offset Voltage

RS ≤ 100Ω

±4

±4.5

±5

±5.5

±6

IOS

Input Offset Current

2.5

μA

Input Bias Current

μA

Input Voltage Range

Single 5V Supply

–3.75

1.25

3.5

–3.75

1.25

3.5

–3.75

1.25

3.5

–3.75

1.25

3.5

–3.75

1.25

3.5

CMRR

Common Mode

Rejection Ratio

–3.75V ≤ VCM ≤ 3.5V

PSRR

Supply Voltage Rejection Positive Supply

4.6V ≤ V+ ≤ 5.4V

Negative Supply

–7V ≤ V– ≤ –2V

Small-Signal Voltage

Gain

1V ≤ VOUT ≤ 2V

1300

1200

1100

1000

900

V/V

VOH

Output High Voltage

V+ ≥ 4.6V, IOUT = 1mA

2.65

2.64

2.63

2.60

IOUT = 10mA

2.40

2.39

2.38

2.35

VOL

Output Low Voltage

ISINK = 4mA

0.55

0.56

0.57

0.6

I+

Positive Supply Current

I–

Negative Supply Current

IIL

LATCH Pin Current

VLATCH = 0V

525

575

650

725

800

μA

tPD

Propagation Delay

ΔVIN = 100mV, OD = 5mV

416

ΔVIN = 100mV, OD = 20mV

414

10KRAD(Si) 20KRAD(Si) 50KRAD(Si) 100KRAD(Si) 200KRAD(Si)

ΔtPD limits shown can be guaranteed with this test if additional DC tests

are performed to guarantee that all internal bias conditions are correct. For

low overdrive conditions, VOS is added to overdrive.

Note 5: Electrical speciﬁcations apply only up to 5.4V.

Note 6: Input voltage range is guaranteed in part by CMRR testing and

in part by design and characterization. See the LT1016 data sheet for

discussion of input voltage range for supplies other than ±5V or 5V.

Note 7: This parameter is guaranteed to meet speciﬁed performance

through design and characterization. It has not been tested.

RH1016M датащи(PDF) 3 Page - Linear Technology

RH1016M датащи(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6

датащи скачать

ссылки URL