TDF8553J datasheet(8/47 Pages) NXP

8 / 47 page

TDF8553J_1

Objective data sheet

Rev. 01 — 3 December 2008

8 of 47

NXP Semiconductors

TDF8553J

× 50 Watt power ampliﬁer and multiple voltage regulator

Functional description

The TDF8553 is a multiple voltage regulator combined with four independent audio power

ampliﬁers conﬁgured in bridge tied load, with diagnostic capability. All regulator output

voltages except regulators 2 and 6 can be controlled via the I2C-bus.

The ampliﬁer diagnostic functions give information about output offset, load, or

short-circuit. Diagnostic functions are controlled via the I2C-bus. The TDF8553 is

protected against short-circuit, over-temperature, open ground and open VP connections.

If a short-circuit occurs at the output of a single ampliﬁer, that channel shuts down, and

the other channels continue to operate normally. The channel that has a short-circuit can

be switched off by the microcontroller via the appropriate enable bit of the I2C-bus to

prevent any noise generated by the fault condition from being heard.

8.1 Start-up

At power on, regulators 2 and 6 will reach their ﬁnal voltage when the backup capacitor

voltage exceeds 5.5 V independently of the voltage on pin STB. When pin STB is LOW,

the total quiescent current is low, and the I2C-bus lines are high impedance.

When pin STB is HIGH, the I2C-bus is biased on and then the TDF8553 performs a

power-on reset. When bit D0 of instruction byte IB1 is set, the ampliﬁer is activated, bit D7

of data byte DB2 (power-on reset occurred) is reset, and pin DIAG is no longer held LOW.

8.2 Start-up and shut-down timing

See Figure 12.

A capacitor connected to pin SVR enables smooth start-up and shut-down, preventing the

ampliﬁer from producing audible clicks at switch-on or switch-off. The start-up and

shut-down times can be extended by increasing the capacitor value.

If the ampliﬁer is shut down using pin STB, the ampliﬁer is muted, the regulators and

switches are switched off, and the capacitor connected to pin SVR discharges. The

low-current standby mode is activated 2 seconds after pin STB goes LOW.

8.3 Power-on reset and supply voltage spikes

See Figure 13 and Figure 14.

If the supply voltage drops too low to guarantee the integrity of the data in the I2C-bus

latches, the power-on reset cycle will start. All latches will be set to a predeﬁned state,

pin DIAG will be pulled LOW to indicate that a power-on reset has occurred, and bit D7 of

data byte DB2 is also set for the same reason. When D0 of instruction byte IB1 is set, the

power-on ﬂag resets, pin DIAG is released and the ampliﬁer will then enter its start-up

cycle.

8.4 Diagnostic output

Pin DIAG indicates clipping, thermal protection pre-warning of ampliﬁer and voltage

regulator sections, short-circuit protection, and low and high battery voltage. Pin DIAG is

an open-drain output, is active LOW, and must be connected to an external voltage via an

TDF8553J датащи(PDF) 8 Page - NXP Semiconductors

TDF8553J датащи(HTML) 8 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47

датащи скачать

ссылки URL