AD9520-2SLASHPCBZ datasheet(43/84 Pages) AD

43 / 84 page

AD9520-2

Rev. 0 | Page 43 of 84

DIVIDE BY 1,

2, 3, 4, 5, OR 6

CLK/CLK

DIVIDER

DELAY

DIVIDER

DELAY

PFD

LOOP

FILTER

MUX1

REG 0x01E[1] = 1

REFIN/

REFIN

REG 0x01E[0]

ZERO DELAY

INTERNAL FEEDBACK PATH

EXTERNAL FEEDBACK PATH

ZERO DELAY FEEDBACK CLOCK

CHANNEL DIVIDER 0

CHANNEL DIVIDER 1

CHANNEL DIVIDER 2

CHANNEL DIVIDER 3

OUT0 TO OUT2

OUT3 TO OUT5

OUT6 TO OUT8

OUT9 TO OUT11

AD9520

Figure 48. Zero Delay Function

ZERO DELAY OPERATION

Zero delay operation aligns the phase of the output clocks with

the phase of the external PLL reference input. There are two zero

delay modes on the AD9522: internal and external.

Internal Zero Delay Mode

The internal zero delay function of the AD9520 is achieved by

feeding the output of Channel Divider 0 back to the PLL N

divider. In Figure 48, the change in signal routing for internal

zero delay mode is shown in blue.

Set Register 0x01E[2:1] = 01b to select internal zero delay mode. In

the internal zero delay mode, the output of Channel Divider 0 is

routed back to the PLL (N divider) through Mux3 and Mux1

(feedback path shown in blue in Figure 48). The PLL synchronizes

the phase/edge of the output of Channel Divider 0 with the

phase/edge of the reference input.

Because the channel dividers are synchronized to each other,

the outputs of the channel divider are synchronous with the

reference input. Both the R delay and the N delay inside the PLL

can be programmed to compensate for the propagation delay

from the output drivers and PLL components to minimize the

phase offset between the clock output and the reference input to

achieve zero delay.

External Zero Delay Mode

The external zero delay function of the AD9520 is achieved by

feeding one clock output back to the CLK input and ultimately

back to the PLL N divider. In Figure 48, the change in signal

routing for external zero delay mode is shown in red.

Set Register 0x01E[2:1] = 11b to select the external zero delay

mode. In external zero delay mode, one of the twelve output clocks

(OUT0 to OUT11) can be routed back to the PLL (N divider)

through the CLK/CLK pins and through Mux3 and Mux1.

This feedback path is shown in red in Figure 48.

The user must specify which channel divider will be used for

external zero delay mode in order for VCO calibration to work

correctly. Channel Divider 0 is the default. Channel Divider 1,

Channel Divider 2, or Channel Divider 3 can be selected for

zero delay feedback by changing the value in Register 0x01E[4:3].

The PLL synchronizes the phase/edge of the feedback output

clock with the phase/edge of the reference input. Because the

channel dividers are synchronized to each other, the clock outputs

are synchronous with the reference input. Both the R delay and

the N delay inside the PLL can be programmed to compensate

for the propagation delay from the PLL components to minimize

the phase offset between the feedback clock and the reference input.

AD9520-2/PCBZ датащи(PDF) 43 Page - Analog Devices

AD9520-2/PCBZ датащи(HTML) 43 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

датащи скачать

ссылки URL